PDA

View Full Version : Peel n Seal



JiggaD369
11-20-2004, 10:28 AM
ok. ive done searched on and read every thread n post made on peel n seal but noone seems to answer my question. many poeple say its great but some still say it ***** and falls off. many responded to that, that u have to prep the surface well and use a heat gun to make it stick. if it does stick then my question is, does it produce any fumes from heat? cuz i dont wanna put it on and have all kinds of chemcal fumes in my car. please help me out. thanx.

iamamp3pimp
11-21-2004, 03:14 AM
id like to know this also

Radar
11-21-2004, 04:00 AM
I've messed with this a little bit, but not a whole lot. Prepping is key, use paint thinner to prep. Heat gun was not needed in my case.Fumes are not a factor for me, but my trunk is pretty well sealed off from the car.

boister77
11-21-2004, 04:06 AM
i have about 100 sq. ft. installed and i have yet to have problems. it went up to 100 degrees this summer so it was probably 110+ in the car. i didn't notice and peeling or any fumes. it's holds up well and does a decent job.

c0la
11-21-2004, 04:15 AM
2nd ^ I also have over a 100 sq. ft. of p&s in the cabin of my car front to back, no smell whatsoever from day one. Also in my door skin and if it would have fallen, then my window would show evidence of it falling down after 6 mo. of applying it

JiggaD369
11-23-2004, 01:10 PM
has anyone noticed any fumes and/or smell except cOla?

Simos
11-23-2004, 07:44 PM
no fumes, no heat gun, and I did virtually no prep either. I have had two layers on both doors for nearly 6 months now. Had the door panels off a few weeks ago and pulled on the peel and seal, couldnt get that stuff of if I wanted to, stuck really well.

themainjam
11-23-2004, 07:59 PM
on doors do you put it on the outside panel(if the car got dented so would the peel seal) or on the surface where the speakers mounts?

supa_c
11-23-2004, 08:10 PM
is that a joke ?

pks71
11-23-2004, 08:52 PM
is that a joke ?
I think you misunderstood him.
The answer you can do both. The purpose of this is to add weight and make the door solid instead of tinny.

themainjam
11-23-2004, 10:30 PM
cmon supa you know i aint that crazy..... or maybe i am :P

hmm ok i understand now. i just thought it would be a pain on the but to get the stuff perfect on the inside. so i think i will do both :)

supa_c
11-23-2004, 10:36 PM
It really seemed like you meant that though.
You arent THAT dumb ;)
I think im gonna get some of this sfuff

themainjam
11-23-2004, 10:41 PM
lol i just reread it and it did sound that way :P

but i meant on the inside of the outer panel :)
but thanks for the help :)

Sleeklsc
11-23-2004, 10:57 PM
"IF YOUR PROPERLY APPLY IT nothin will happen..i used it on my entire trunk and have not experienced it peeling..the only reason it would fall off is if it was not put on properly...all you have to do is clean the suface with soap and water, let it dry then put it on..but with any deadner you have to use a strong hand....

no heat gun was needed to put this on..it was VERY sticky...compared to dynamat, fattmat, ect...but you cant install these deadners in colder weather because they will loose the adhsive properties...i'd say 65-70 degrees or warmer...but it all depends, if it seems like it will adhear good give it a shot.."

taKen from 1 of my other posts.... AND IT DOESNT SMELL!

JiggaD369
11-26-2004, 12:10 AM
so i should go with it?

monte_carlo97
11-26-2004, 12:14 AM
i have done peel and seal and there was hardly any fumes. I just used soap and water to clean everything. For application i used a small propane torch to get everything nice and warm and sticky

iamamp3pimp
11-29-2004, 02:15 AM
its gettin cold in vegas so i will need to use some heat. do you use the heat gun to heat the pns itself, or the surface your applying it too

supa_c
11-29-2004, 02:32 AM
It really seemed like you meant that though.
You arent THAT dumb ;)
I think im gonna get some of this stuff
Well, im not gonna use PnS any more.
eDead it is !

iamamp3pimp
11-29-2004, 02:41 AM
isnt PnS cheaper?. i know cheaper isnt always better, but if it works, it works

supa_c
11-29-2004, 02:44 AM
If you woud like to know Pm me and on monday i will have prices.
BTW...this isnt the crappy 45MM stuff
Its the 70MM ;)