PDA

View Full Version : WTT Solo X Motor for Table Saw



*Ace*
04-15-2013, 05:53 PM
1. Product: One 3" Coil Solo X Motor



2. Specs: Solo X Motor



3. Description/Condition:
Mechanical = 10/10
Visual = 8/10, needs the glue cleaned up and looks like there are a few strands of voice coil to be removed from inside gap (from previous owner).



4. What you are looking for: : New or very good condition 10" table saw (with blade) with >= 36" bar clamps.



5. Pictures of your item for trade:
http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0822_zps1ff8b2fe.jpg

http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0823_zps07506a68.jpg

http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0824_zps02309fb8.jpg

http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0825_zps7e866a88.jpg

http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0826_zpse433f1fd.jpg

http://i816.photobucket.com/albums/zz87/jc_smith/IMG_0827_zpsb44b4687.jpg

fasfocus00
04-15-2013, 06:40 PM
you want to trade that motor for a table like this?

http://i246.photobucket.com/albums/gg120/fasfocus00/E0DDE853-F609-4995-8BCE-7269B06A2913-16757-00000E7A4DC29294_zpsba3aac9a.jpg (http://s246.photobucket.com/user/fasfocus00/media/E0DDE853-F609-4995-8BCE-7269B06A2913-16757-00000E7A4DC29294_zpsba3aac9a.jpg.html)

rebelfromva
04-15-2013, 08:53 PM
This from a 10" solo x?

Ronny
04-15-2013, 09:45 PM
I was about to ask what size driver it came off of too. Or, perhaps OP if you could simply take a pole piece or gap measurement (gap's O.D. or Top Plate's I.D.). Being that if the gap is near 3.5" diameter, it'd be an 18" motor, and if near 3" it be a smaller size motor. But from the pole piece protruding out so much, I'm pretty sure it is not originally off of an 18" with 3.5" coil, rather a smaller one. But if it happens to be a 3.5" coil I'll PM you with an offer because I'd like to obtain a matching motor... And I have two table saws at the moment :)

*Ace*
04-15-2013, 10:26 PM
This motor came off a 10" Solo X, so it's the 3" version, not the 3.5" version.

Pole OD = 2.9100"
Top Plate ID = 3.2265"

TheycallmeJT
04-15-2013, 10:50 PM
How much would you sell it out right for. I've got a 10" x sitting in a box in the closet. Could be interesting reconing them into something

04murdalanche
04-15-2013, 11:16 PM
How much would you sell it out right for. I've got a 10" x sitting in a box in the closet. Could be interesting reconing them into something

This

Zeuslicious
04-16-2013, 02:33 AM
Nooooooooooooooo! Lol

*Ace*
04-16-2013, 03:17 AM
you want to trade that motor for a table like this?

http://i246.photobucket.com/albums/gg120/fasfocus00/E0DDE853-F609-4995-8BCE-7269B06A2913-16757-00000E7A4DC29294_zpsba3aac9a.jpg (http://s246.photobucket.com/user/fasfocus00/media/E0DDE853-F609-4995-8BCE-7269B06A2913-16757-00000E7A4DC29294_zpsba3aac9a.jpg.html)

I should specify. Obviously I don't expect to get a $600 dollar table saw, but am referring to the cheaper Ryobi ones or similar that can be found at home depot for under $200. As for a straight up selling price I'm not sure. PM me an offer if you just want to outright buy the motor