PDA

View Full Version : FS 2 MTX 81000d's and matching 4 channel



Laneyrw
03-31-2013, 04:38 PM
Item(s) for Sale:
I have a mtx 81000d and a matching mtx four channel 4244 all in great working order



Item(s) Description/Condition:
81000d's are modded so the will run on 1 ohm and will put out around 2000rms. Cosmetically it is 7/10 looks very well for its age. The mtx 4434 works great and puts out around 50 rms per channel and is 8/10 on looks atleast. I'm selling because of a deal i found but i would trade for nice 3500 watt amp at 1 ohm. Sorry the date on the pic is a little off I took them a couple weeks ago.



Price:
225 for the 81000d
80 for 4244



Shipping and Miscellaneous Item Information:
U pay



Item Pictures:
(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).

jteske88
03-31-2013, 06:06 PM
Can u explain said mod?

Laneyrw
03-31-2013, 06:28 PM
They were modded when I bought them and was told it was professionally done all that is done is one of the chips is removed. This makes it so they can run at 1 ohm. When I bought them I made sure that chip was removed and tested them at 1 ohm to make sure they work properly

tprj82
03-31-2013, 09:09 PM
it was a very common and relitivly safe mod could go down to .7 with ample voltage i had a pair of these powering a pair of 15 in squares back in the day great amps good luck with sale

Sleeklsc
03-31-2013, 09:37 PM
Some saved pm's i've had for 8 years. lol


Modding it is pretty easy if you're familiar with removing circuits with a soldering iron. You have to remove resistor Q240 from the board and release the compression circuit. .


The dont do it from the factory because the chip you remove is the part of the protection circuitry that shuts the amp down if it see's a load below 2 ohms (ie dead short) so when modded you have to be careful not to touch the speaker leads together while the amp is on, or you will short it out. And yes the mod will allow up to 18.5 dc volts and down as low as you feel comfortable on impedance... I wouldnt suggest any lower than .5 for daily.


q 240 is located in the south west quadrant of the amp... you have to be careful to not remove d240 that is right beside it. Also, the compression circuit is a little white button next to the rca end of the amp. It needs to be pushed in the "out" position.
Good luck,
Scottie

I ran mine modded for some time @ .67. It was a powerhouse!

This setup right here will get nasty.

Sub Woofin
04-01-2013, 12:42 AM
how much for just the 4 channel?

pickup1
04-01-2013, 08:27 AM
Or 1 mono amp...

BlurredVision
04-01-2013, 10:20 AM
I've heard one of these before modded and they play / sound great

Laneyrw
04-01-2013, 06:29 PM
I not sure what a nice used saz3500v2 goes for used but I'd throw in my aq2200 and all the rest on a trade

GeekSquad
04-02-2013, 02:45 AM
I would partial trade a Powerbass XA4000D for these. We could work out the cash on top of that if you like?

tprj82
04-02-2013, 09:44 AM
your only looking to step up a few hundred watts? you should be getting almost 3500 out of a pair of those strapped arent you?

Laneyrw
04-02-2013, 12:35 PM
I need 1 ohm final and these do 1 ohm each and 2 strapped. Also just wanting 1 amp was hoping sundown to match my highs amp. But any 3500 plus will work

tprj82
04-02-2013, 03:03 PM
ahhh I see, good luck with sale wish i was in the market for something these they would be gone

Laneyrw
04-02-2013, 09:06 PM
Geeksquad clear your inbox I am interested send me a pm with your offer

Laneyrw
04-07-2013, 03:34 PM
One 81000d left and the 4244 still available a nice 4 channel for cheap