3 in each door?

[Bassin Buick]

Bravox WFR-06BV03B 6-1/2" Silver Cone Shielded Woofer 12 Ohm (http://www.parts-express.com/pe/pshowdetl.cfm?&Partnumber=299-057)

think they would be decent??

[Bassin Buick]

BTW , they would be running bandpassed off of a hifonics eagle bridged to 2 channels.

Would go in a sealed fiberglass pod below the door panels in my truck.

[Bassin Buick]

nobody at all??

[CHEMMINS]

Meh....bravox are usually overpriced....but those are cheap.

High qts though....not too cool for doors.

[Bassin Buick]

gonna be in a sealed fiberglass pod. high qts usually needs small sealed enclosures right? I'm not too hip to the t/s stuff.

[CHEMMINS]

high qts = big box

[CHEMMINS]

2.47 cubes needed for 3 to have a flat roll off with -3db at 80hz

[Bassin Buick]

ran the t/s through bassbox pro. gives me a f3 of 100hz with 3 of them in .5 sealed with heavy poly fill. Not that bad.

[Bassin Buick]

2.47 cubes needed for 3 to have a flat roll off with -3db at 80hz

OUCH!! thats huge!

[CHEMMINS]

Yep.....they are made for HT usage....

[Bassin Buick]

so i need to be looking for low QTS?? i'm trying to do a multi woofer setup in the doors with some of the buyout type speakers. something dirt cheap but still good quality. :)

[CHEMMINS]

https://www.madisound.com/store/product_info.php?cPath=45_228_256&products_id=8405

Run 2 in each door.....better bet. 1.63 cubes for 2.....to get a -3 db at 80hz

[CHEMMINS]

These are what I wanna run....

Peerless 831735 6-1/2" HDS Driver (http://www.parts-express.com/pe/pshowdetl.cfm?&Partnumber=299-281&scqty=2)

1 cube for 2 to tune to -3db at 70 hz.

Could go slightly smaller box and gain a lil before roll off.

[Bassin Buick]

i've been thinking about those too. but if i go with 2 per door i'm gonna go 8" because i have the room for bigger mids. were talking about a '85 F-150 here. LOL

prolly just stick with my original plan to use 2 8ohm silver flutes per door. any 8 ohm 8" models you think i should look at? remember i'm not running gobs of power only about 150x2@4 for the mids.

[CHEMMINS]

Dayton Audio DC200-8 8" Classic Woofer (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=295-310)

1.2 cubes for 2......-3db at 60 hz

[Bassin Buick]

Dayton Audio DC200-8 8" Classic Woofer (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=295-310)

1.2 cubes for 2......-3db at 60 hznice! i got .4 cubes with a f3 of 75hz (which is all i really need)!! maybe i will try these??

[CHEMMINS]

For the price....you really can't go wrong.

[Bassin Buick]

i think i'm gonna go with them. i gotta sell a few computers on CL then i will prolly be getting these. Any good recommendations on tweeters? i already have 4 of these and was prolly gonna use them. (one set low in the pods , and one set low in the a-pillars)

Vifa BC25SC06-04 1" Textile Dome Tweeter (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=264-1028)

they get loud as **** on small power and still sound good doing it. will get 45 each off of my hifonics hawk.

[CHEMMINS]

I'd only use 1 set.

But what are ya gonna use to fill mid from 1000 hz to 3500 hz?

[Bassin Buick]

also was thinking i may try these Dayton Audio SD315A-88 12" DVC Subwoofer (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=295-488) behind my seat in a sealed box getting 165 each off my usacoustics 4065.

[Bassin Buick]

I'd only use 1 set.

But what are ya gonna use to fill mid from 1000 hz to 3500 hz?

well i hadn't thought of that because the midbass drivers i was looking at before went up to 3K. LOL.

well i guess i better keep searching. LOL

[CHEMMINS]

Use those subs, the 8" midbass, XXXX for mids...and one set of tweeters. Nice active setup.

[Bassin Buick]

I'd only use 1 set.

But what are ya gonna use to fill mid from 1000 hz to 3500 hz?

just took a look at the spec sheet on those dayton classic 8". there is a HUGE dip in response between 1k and 3K. LOL. gotta try something different then. i don't wanna run a 3 way front stage and that would alomst be a must if i used those woofers.

[CHEMMINS]

You wont find a decent midbass that plays well up to 3500 without major ripple. You could however get a full range, and play down to 1000 hz....something like these:

http://www.hybrid-audio.com/Legatia%20L3.pdf

[Bassin Buick]

maybe run a passive crossover between the mid and tweet and still use the hawk to power that setup? mid and tweet in the a-pillars?

[Bassin Buick]

You wont find a decent midbass that plays well up to 3500 without major ripple. You could however get a full range, and play down to 1000 hz....something like these:

http://www.hybrid-audio.com/Legatia%20L3.pdf

hat is too expensive. i'm working on a very tight budget. i'm looking for good but cheap. LOL.

[CHEMMINS]

Yeah...passive mid/tweet......run the midbass seperate, and the 12's

[Bassin Buick]

gonna have to do that. i only have the 3 amps and no room for more amps. LOL.

LMAO go here and click the link for the specs sheet. FAIL!!!

Tang Band W4-1052SD 4" Driver 4 Ohm (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=264-828)

[Bassin Buick]

how about these for mids? Dayton Audio RS100-4 4" Reference Full-Range Driver 4 Ohm (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=295-378)

[CHEMMINS]

gonna have to do that. i only have the 3 amps and no room for more amps. LOL.

LMAO go here and click the link for the specs sheet. FAIL!!!

Tang Band W4-1052SD 4" Driver 4 Ohm (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=264-828)

Errrr.....nice horn?

[CHEMMINS]

The RS-100's are supposed to be nice drivers for the price.

[Bassin Buick]

Errrr.....nice horn? lulz were had.

[Bassin Buick]

The RS-100's are supposed to be nice drivers for the price.

think they really play smooth up to 20K?

[CHEMMINS]

think they really play smooth up to 20K?


Nope....maybe 10k

[Bassin Buick]

i figured. how about a single pair of these Dayton Audio SD215A-88 8" DVC Subwoofer (http://www.parts-express.com/pe/pshowdetl.cfm?&Partnumber=295-484&scqty=2) for midbass since we are talking about a 3 way setup.

play them up to around 800hz , 800-5K for the mids , and then the tweets playing up from where the mids are cut off at?

[CHEMMINS]

They will be about the same as the other set....

Ideally you would x at 1k, and 3500 for mb/m/t

[Bassin Buick]

ok. well i guess i now have a nice idea of what i'm gonna start with in there.

Hifonics Hawk At 1k HP Running the RS-100's and Vifa Tweets passively crossed over at around 3.5k

Hifonics Eagle Bandpassed At 80-1k Running the pair of 8" DVC's

And the usacoustics 80hz LP on the 2 DVC 12's

Nice. should come out pretty decent. I want a speaker system that i can impress with and impress even more when they find out all of them together cost around 200 bucks total. LOL.

Thanks chemmins.

[CHEMMINS]

Anytime man...and yes it can be done on the cheap if ya do a lil research first!

[Bassin Buick]

Nice. i think it's gonna be sweet.

[82 cutlass]

i think i'm gonna go with them. i gotta sell a few computers on CL then i will prolly be getting these. Any good recommendations on tweeters? i already have 4 of these and was prolly gonna use them. (one set low in the pods , and one set low in the a-pillars)

Vifa BC25SC06-04 1" Textile Dome Tweeter (http://www.parts-express.com/pe/showdetl.cfm?Partnumber=264-1028)

they get loud as **** on small power and still sound good doing it. will get 45 each off of my hifonics hawk.

Those are some good tweeters . I have 4 and they sound great and get loud

[Bassin Buick]

hey chemmins. i was playing with the specs on those 8" dvcs and with .277 sealed i'm showing a f3 of 66hz! or .44 for 60 even. :) NICE!!!

[CHEMMINS]

Is that per driver or for the pair?

[Bassin Buick]

per driver. remember they are 8 ohm dvc's so it will only be 1 per door.

[CHEMMINS]

Ah yeah.....I would run the svc ones.....get 2........+3db right there.

[Bassin Buick]

true.