PDA

View Full Version : component speaker messed up, anyway to fix it?



thaster
04-25-2010, 01:41 PM
well one of my crossover for my Crystal SSCS6 speakers crap out on me. I can't find a replacement so are there any other crossover i could replace it with?

thaster
04-25-2010, 09:11 PM
anyone?

kevin lu
04-27-2010, 03:17 AM
go here
Equalizers - Crossovers (http://www.woofersetc.com/index.cfm?currentpage=8&fuseaction=category.display&category_id=11)

sdmtnbiker420
04-27-2010, 03:26 AM
did you check all your wiring connections

thaster
04-27-2010, 03:28 AM
the crossover coils became untangled

sdmtnbiker420
04-27-2010, 03:29 AM
nice!

thaster
04-27-2010, 03:29 AM
go here
Equalizers - Crossovers (http://www.woofersetc.com/index.cfm?currentpage=8&fuseaction=category.display&category_id=11)

can i replace it with a different brand?

sdmtnbiker420
04-27-2010, 03:30 AM
i would

thaster
04-27-2010, 03:34 AM
i would

but i thought the crossover were set specifically for the speakers.

sdmtnbiker420
04-27-2010, 05:17 AM
nah as long u get a crossover for the same impedance speaker it should be fine.

thaster
04-27-2010, 09:20 PM
nah as long u get a crossover for the same impedance speaker it should be fine.

u sure?

QuikSilverRS91
04-27-2010, 10:35 PM
Personally, I would buy a pair of crossovers and replace them both just for uniformity. But that's just how I roll.

You'd be fine just replacing the 1 though. Depending on how BAMF your hearing is you might notice a slight difference between the left and right.

thaster
04-28-2010, 12:48 AM
ok thanx for the clarification

Louisiana_CRX
04-28-2010, 12:52 AM
run them active and enjoy pure clean sound the way it was suppose to be heard .......

KyleBechtold
04-28-2010, 12:55 AM
run them active and enjoy pure clean sound the way it was suppose to be heard .......

active means you set your own xovers not that the sound is more pure.. I am sure you know this but owell

op.. if you can find out what the xover points are you can get another xover with similar specs.. or have one made or make one..

thaster
04-28-2010, 12:58 AM
how would i find out the crossover points? here are the specs: http://www.crystalmobilesound.com/specifications.asp i have the sscs6

KyleBechtold
04-28-2010, 01:04 AM
[email protected]

email them and ask what the xover points are for your comps and ask if they have them for sale aswell if not ask if any of there other comps use similar or identical xover points

thaster
04-28-2010, 01:09 AM
[email protected]

email them and ask what the xover points are for your comps and ask if they have them for sale aswell if not ask if any of there other comps use similar or identical xover points

the company went down under like 2 years ago :( what now?

thaster
04-28-2010, 11:25 AM
anyone?

thaster
04-29-2010, 01:10 AM
anyone?

KyleBechtold
04-29-2010, 01:11 AM
are both xovers shot?

KyleBechtold
04-29-2010, 01:12 AM
if one is fine you can look at the part thats broken on the one and replace it

thaster
04-29-2010, 01:17 AM
the inductor wire coil became loose from the board and it untangled itself. I was thinking if it is possible to just solder a new .8mH inductor onto the board