View Full Version : T-LINE for DD9915
04-04-2010, 03:38 PM
Ok so it doesnt look like im going to get rid of my 9915's.. so is there anyone out there that can build me a t-line enclosure for 1 of them to fit in the back of an 03 impala?? I have built ported and vented, but this t-line **** is way to complicated for me.
04-04-2010, 03:40 PM
hope you have a huge trunk.
04-04-2010, 03:41 PM
Hitup Ami Creations he wil do it and get it done nice..
Heres some of his work..
Ami Creations Portfolio - Car Audio Classifieds (http://www.caraudioclassifieds.org/forum/showthread.php?t=28007)
Tell him i sent ya:)
04-04-2010, 03:49 PM
huge trunk huh.. i was hoping to fit one in a t-line enclosure, due to the fact i cannot fit both in my truck in a ported
04-04-2010, 04:32 PM
15" in a T Line. **** is HUGE.
04-04-2010, 04:44 PM
that would prolly fit in my trunk, you know dimensions on it??
04-04-2010, 04:50 PM
i cant imagine that **** fitting in a trunk ha that looks to be at least 40 inches long maybe
04-04-2010, 04:54 PM
it would fit width and height wise, i just dont know about depth
04-04-2010, 04:57 PM
44 inches in length. those impalas must be huge in the trunk.
04-04-2010, 04:59 PM
not sure on depth
04-04-2010, 04:59 PM
you dont have 40" wide avalable and unless you remove the rear 6x9's you only have like 15" height..
04-04-2010, 05:00 PM
box was built by groundpound here on these forums
04-04-2010, 05:03 PM
what are your t/s specs for that sub?
that line is tuned to 24hz and is for a 12, i currently have a DD 1512 in there. i built it for an IDQ12, the IDQ played the higher notes and sounded somewhat clearer, but the DD still sounds good and is better suited for it, gets lower and louder.
I could have made it less longer by adding another bend but either way it would of ended up big.
04-04-2010, 05:06 PM
nice box super. that 49" is killer
build thread for the 15" t line - sort of
04-04-2010, 05:10 PM
i do have 40" wide.. i am fine with losing the 6x9's.
04-04-2010, 05:13 PM
really cause my 05 didnt have 40" wide you plan on doing the build in the trunk i take it..
04-04-2010, 05:16 PM
making another bend would increase the depth to about 28 inches or so? reducing the height to under 40 maybe? but then again thats a 12in.
04-04-2010, 05:17 PM
bend would reduce, hmm. let me figure it out i was actually thinking of doing it. going to be building one for 2 6.5" subs soon lol.
04-04-2010, 05:22 PM
yea in the trunk
04-04-2010, 05:24 PM
reduce the 49 to 35 and make the 21 a 27.75"
for a 15" sub i would make the height 16/17" but that would limit 6.75" mounting depth, you could just add baffles. Also if you line doesnt need to be tuned that low you would have a way shorter line. It could be possible, provide t/s specs...
04-04-2010, 05:37 PM
vas=85L, qms=4.32, qes=0.31, qts=0.29, Free Air Resonance=33hz, and they are dual 1 ohm vc's
04-04-2010, 06:03 PM
mounting depth= 8.5in would put it touching mdf, so 9in would give you 1/2in of clearance
04-04-2010, 06:20 PM
soooo... anyone got any ideas?
04-04-2010, 07:15 PM
anyone in TN able to build one?!
04-04-2010, 08:48 PM
there is no sd spec... pm me pics with a tape measure across the top of the sub, surround to surround.