PDA

View Full Version : 6.5 comps on 75w rms



VIP3R
01-05-2010, 10:03 PM
what do you guys recommend?
ive been doing my research..
only have 75w rms to work with atm as well.
been looking around...but it seems everyone goes over the RMS anyway..

ive been looking at the pioneer ts-d720c, and id ctx65cs and a few others....
even kicker and the phoenix gold...

i have 6x8s atm and want to upgrade... my current 6x8 get loud

do any of these get loud as well?

thanks

hatemonger
01-05-2010, 10:08 PM
ID and phoenix gold are good choices. never messed with the other 2.

Villeza1
01-05-2010, 10:08 PM
phoenix gold

Hoodlum007
01-05-2010, 11:58 PM
ID CTX's all the way sir.

VIP3R
01-06-2010, 04:38 AM
would they work well off 75 w rms? how loud would they get compared to what i have now?

SicAudio
01-06-2010, 04:48 AM
you need a more efficient speaker to run on 75rms so look at 50-75 rms drivers to get the most from them. the opti line is good so are pg or mbquart f or d series

VIP3R
01-06-2010, 04:57 AM
any recommendations other than those?
how are the kicker 650.2 (not so great id imagine?) they handle 75w rms though
or do the pioneer ts-d720c get loud?

SicAudio
01-06-2010, 05:10 AM
6-1/2" 2-way Component System (Marine Certified)
Power Handling:
Peak: 600 watts per set / 300 watts each side
RMS: 200 watts per set / 100 watts each side
Aerated Polypropylene Cone
Removable Phase Plug
Butyl Rubber Surround
Neodymium Magnet Structure
Die Cast Aluminum Basket
U.S. & Euro hole patterns to line up with the mounting screw holes of virtually any vehicle
1 1/2” Voice Coil
Polyimide Voice Coil Former for high thermal stability
4-Way Gold Plated Input Terminals Corrosion resistant terminals
Vent Holes in the basket equalize air pressure on both sides of the spider for more linear travel, flatter frequency response and lower distortion
1" Ring Radiator Tweeter
Neodymium Motor Structure with Faraday Cap
High Frequency Waveguide Prevents phase cancellations for smooth, uniform frequency response and wide dispersion
Zoebel Crossover Network flattens the system impedance curve for more efficient power transfer and flatter response
Air Core Inductors with Oxygen Free Copper wire, for wider dynamic range, contrast and punch
Mylar Capacitors
Tweeter Protection Circuit
Gold-plated connectors
Cast-Aluminum heat sink
2nd Order Low Pass Filter
3rd Order High Pass Filter
Frequency Response: 40 - 23,000 Hz
Sensitivity: 92 dB
4 ohm Impedance


http://koby-international.com/images/Product/medium/1228.jpg

VIP3R
01-06-2010, 05:23 AM
those dont look terrible

SicAudio
01-06-2010, 05:32 AM
polk db pretty **** nice for a mainstream brand ;)
not my favorite but not on my no list by any means lolz
thats why i started selling polk

then there are these: DLS classics :) bad *** SQ speakers from scandinavia
http://koby-international.com/images/Product/medium/619.jpg

Woofer size 16,5 cm / 6,5"

Power handling capacity 50 W RMS / 80 W max

Tweeter 16 mm / 0,63"

Frequency range 50-18.000 Hz

Crossover point (Hz) 6000 Hz

Sensitivity 91 dB (1W/1m)

Outer diameter of woofer 165 mm / 6,5"

Magnet size 80 mm / 3,15"

Crossover Cable filter with 12/12 dB slope (LP/HP)

Mounting depth 63 mm / 2,48"

Mounting hole 146 mm / 5,75"

Impedance 4 ohm


notice they have hand made pulp speaker cones?
best sq there is ... paper :)

VIP3R
01-06-2010, 05:39 AM
those are neat too..
what about the ones i mentioned above? like pioneer and kicker

SicAudio
01-06-2010, 05:43 AM
they are ok at best not horrible but dont pay alot for them

VIP3R
01-06-2010, 06:00 AM
im just looking for better performance than my 6x8s without paying a fortune and using the 75 w rms i have for now...
thats all

Hoodlum007
01-06-2010, 12:18 PM
The ID's are rated at 100 watts rms and very efficient on power, 75 watts rms power will get them loud.

VIP3R
01-06-2010, 09:01 PM
thats good to know!
anyone run them with 75?
like know that for a fact?

Adnan86
01-11-2010, 12:10 AM
i have the same thread- still kinda lost on what to get...

ricktcole
01-12-2010, 12:57 PM
Try Boston acoustic Sr65 comp. they are rated at 85 rms I have them in my 4runner and they sound great.I would stay away from the kickers I listened to several setup with them when I was looking for my front speakers. They just didn't sound clean to me. This is just my opinion.