PDA

View Full Version : 3 3" aero's 15 inch long?



bassman3
12-18-2009, 06:48 PM
That equals around 21 square inches correct? You think that would be enough (i know on the low side) for 3 cubes? I never really deal too much with aero's..

Thanks

fasfocus00
12-18-2009, 08:24 PM
why would you run 3 3" aero and not just run a single 6" aero?

basscort2009
12-18-2009, 08:27 PM
That equals around 21 square inches correct? You think that would be enough (i know on the low side) for 3 cubes? I never really deal too much with aero's..

Thanks

clearly. for aeros its better if you run one bigger port instead of more smaller ports. just do a 6

spltuscon
12-18-2009, 08:29 PM
Yes its 21".

You could get away with it on low power, but its too small to perform well at higher power levels.

As mentioned above, a single 6" would be a better choice.

RAM_Designs
12-18-2009, 08:35 PM
A full length 6"er would be better and only raise your tuning 1 cycle.

bassman3
12-19-2009, 04:03 AM
Yea, that's what I was gonna do (go with a single 6") but I would need it to be 20" long and the max depth for the customer is 21".. Is there any problems with there only being 1" from the end of port to the back baffle? or is there not any problems with that? I am not sure if there is suppossed to be a rule (i.e make sure there is at least 3" from end of port to baffle) or something like that..

Thanks

fasfocus00
12-19-2009, 04:14 AM
get an elbow or maybe even just a regular square port

bassman3
12-19-2009, 04:25 AM
Nah. Customer doesn't want a square port. Is there a certain amount of space that should be between the end of port to back baffle?

fasfocus00
12-19-2009, 11:05 AM
Nah. Customer doesn't want a square port. Is there a certain amount of space that should be between the end of port to back baffle?

you can't put the port on a different wall? just get a 90* elbow, problem solved. you want atleast the radius of the port worth of distance from the port in all directions.

MisterGrubbs
12-19-2009, 11:14 AM
Could you not effectively use two 6" port at 10" of depth each?

spltuscon
12-19-2009, 11:48 AM
Could you not effectively use two 6" port at 10" of depth each?

That would raise his tuning a lot since its twice the port area and half the length....

bassman3
12-19-2009, 03:34 PM
where can you get elbow's at? I using the 6" precision port... home depot or what?

bassman3
12-19-2009, 10:35 PM
bump

Johnny Law.Lulz
12-19-2009, 10:39 PM
Elbows would be at any plumbing supply store i believe.

bassman3
12-20-2009, 01:00 AM
hmm. You sue they have elbows that will be 6" in diameter??? I haven't come across any, that is going to be a big *** elbow..

fasfocus00
12-20-2009, 01:05 AM
hmm. You sue they have elbows that will be 6" in diameter??? I haven't come across any, that is going to be a big *** elbow..

sewage supply store would have them or you can always look at putting the port at a different wall.

bassman3
12-20-2009, 04:56 AM
well if i were to put it on another wall it would have to be on the side baffle... and its going in a sedan. I dont know how a side firing port would sound in a sedan... you?

spltuscon
12-20-2009, 09:18 AM
Side firing will work better in a sedan trunk anyways. I usually side fire with very good results, and to answer you question about the elbows, yes they are huge in that size, but they are available at Lowes/HD, plumbing house. I'm not sure they would work well with PSP ports though...never tried it. The elbows are something like $20 each or something crazy like that. Just keep it straight and it'll be good.

RAM_Designs
12-20-2009, 01:37 PM
Could you not effectively use two 6" port at 10" of depth each?

:crap:

bassman3
12-20-2009, 03:16 PM
alright. I think i'm just gonna side fire it. Thanks guys