PDA

View Full Version : Check my box...



Buck
02-03-2009, 03:52 PM
This is for an HDC318 :fyi:

Out side dimensions-50.5 width x 20 height x 13 depth

L port will be cut in one of the 50.5 by 20 sides.
The port will be 18.5 x 5.25. The first port length will be 6.25 and the second will be 7.25.

Buck
02-03-2009, 04:03 PM
If I new how to draw it and get it on here I would lol. I have it drawn on paper.

psych0ticnemes1
02-03-2009, 04:06 PM
Newb... ;) Jk.

Buck
02-03-2009, 04:13 PM
Newb... ;) Jk.

:wave: The box for my 15 is now in someone else's vehicle. Good design btw :)

You actually want to check this for me?

psych0ticnemes1
02-03-2009, 04:28 PM
If I have a minute sure, it shouldn't take long. How big is the box supposed to be? What should the tuning be?

Buck
02-03-2009, 04:29 PM
If I have a minute sure, it shouldn't take long.

It's by the recommended specs (I hope)

psych0ticnemes1
02-03-2009, 04:32 PM
I edited it and asked some questions. ^^^

Buck
02-03-2009, 04:34 PM
If I have a minute sure, it shouldn't take long. How big is the box supposed to be? What should the tuning be?

Box is supposed to be about 6 cub ft, and tuning should be about 40 hz.

hoss
02-03-2009, 04:38 PM
this thread title would be great for a ****.

psych0ticnemes1
02-03-2009, 04:41 PM
I figured the expected port length to be 16.5" for a 6 cube net volume box tuned to 40 htz. Is that what you got? The gross size of your box is 6 cubes... There is no way you'll net 6 cubes after port and woofer displacement...

Newb... ;)

Buck
02-03-2009, 04:42 PM
I figured the expected port length to be 16.5" Is that what you got?

about 16", not sure exactly

psych0ticnemes1
02-03-2009, 04:47 PM
I edited the post again. ^^^

Buck
02-03-2009, 04:50 PM
I figured the expected port length to be 16.5" for a 6 cube net volume box tuned to 40 htz. Is that what you got? The gross size of your box is 6 cubes... There is no way you'll net 6 cubes after port and woofer displacement...

Newb... ;)

I was told that by someone (who runs aq and has been very loud with it) to make the box 6 cubic feet and then just make the port.

psych0ticnemes1
02-03-2009, 04:54 PM
Well, that is great and all except you can't figure out port length unless you know what the net volume is supposed to be.

If you base your port length on 6 cubes net but your actual volume is 5 or so, your tuning will be way off. Compronde compadre?

Buck
02-03-2009, 04:55 PM
Well, that is great and all except you can't figure out port length unless you know what the net volume is supposed to be.

If you base your port length on 6 cubes net but your actual volume is 5 or so, your tuning will be way off. Compronde compadre?

That's what I thought :crap:

That box fit perfect.

Buck
02-03-2009, 04:59 PM
How would 52x22x13 with 3.5" wide port with a length of 8.75"

DBfan187
02-03-2009, 05:01 PM
This is for an HDC318 :fyi:

Out side dimensions-50.5 width x 20 height x 13 depth

L port will be cut in one of the 50.5 by 20 sides.
The port will be 18.5 x 5.25. The first port length will be 6.25 and the second will be 7.25.
http://www.epilepsyfoundation.org/local/massri/images/image-check-box_1_1.jpg

psych0ticnemes1
02-03-2009, 05:03 PM
How would 52x22x13 with 3.5" wide port with a length of 8.75"

I'm out of time. If I have time later I'll check it.

Buck
02-06-2009, 02:08 PM
Or I could do a box with the port firing up.

52 x 14.5 x 22.5 with a port 8.5 inches wide on the 14.5 x 22.5 side with single port being 13.25.

Buck
02-06-2009, 03:11 PM
bump

Buck
02-07-2009, 12:05 AM
bump