PDA

View Full Version : RE Audio L-Port question



Bass911
01-15-2009, 09:05 AM
I used the Re Box Calculator to make a box for a xxx12. I've made boxes before, but none with the L-port yet. When I finished with RE calculator the port width was 4 inches and the calculator says it's tuned to 33.6hz. The back part of the L-port will only leave a 2 inch opening and the whole L-port is 4 inches wide. It seems like that 2 inch opening at the back of the L and the Box Right Plate is not big enough? Will that cause any port noise? I'm talking about the opening right behind the sub where the air first starts to come out to enter the 4 inch L shape port. I also thought the xxx12 would need a bigger box?

Undisputed King
01-16-2009, 01:27 AM
Yes if you only have 2" clearance it would change the tuning. How do you only have 2" if its a L port, or is it 2" from the second obstruction? In that case you could make a 90 degree turn once again, but it will slow down your flow because of all the turns. Ports dont have to be entirely inside the enclosure, the port can stick out outside of the enclosure.

bryce-man
01-16-2009, 03:14 AM
it did that a few times for me too
it just didnt recognise that it had to bend again

Bass911
01-16-2009, 04:16 PM
I think you guys don't understand what I am saying. Go to the Re site and input these numbers (BW 24, BH 18, BTD 24, BBD 24, WT 0.75, SPW 4.0, Sqare port lenght 16.5) and you will see what I'm saying. The tuning will come out to 33.6hz. Look at the box preview window and look at how small that opening will be right behind the subwoofer leading out into the 4 inch L-port. I had to do the math to find out that it was only 2 inches. I did the math because the box preview looked wrong. I might be wrong?

mazdakid
01-16-2009, 06:41 PM
make the box wider, or make a smaller port. you dont need 20sq" of port per cube.

Bass911
01-16-2009, 09:56 PM
The wider and deeper I make te box makes the tuning too high according to the RE Calculator.

mazdakid
01-16-2009, 10:17 PM
Its because you have so much port area. What size and tuning are you looking for? What kind of car is it going in?

Bass911
01-17-2009, 05:27 AM
I think I figured it out. Thanks!

Bass911
01-17-2009, 05:29 AM
I was messing up the square port length, but I figured it out.

19992wdtaco
01-17-2009, 08:10 PM
How accurate can that box calculator be when it doesn't even ask for sub displacement?

ARSkemp
01-17-2009, 08:42 PM
with a single 12 disp shouldn't effect tuning much, your tuning frequency shouldn't raise more than 1hz after tuning.

Just make the box w/a tuning .5-1hz below what you want, possible more depending on how much bracing, if any your going to use.

Bass Addict
01-17-2009, 08:46 PM
i read on another forum that RE-calculator is off 2-3 tunig hz.what i mean is say if the box is tuned to 33 with re,then its actually going to be around 35-36

MotoRacer243
01-17-2009, 08:54 PM
i read on another forum that RE-calculator is off 2-3 tunig hz.what i mean is say if the box is tuned to 33 with re,then its actually going to be around 35-36


Thats pretty consistent with my findings too.

19992wdtaco
01-17-2009, 09:05 PM
What tuning is good for one that listens to mostly heavy metal and occasional rap?

mazdakid
01-17-2009, 09:23 PM
you guys that think its 2-3hz off, what do you use to calculate tuning?

Bass Addict
01-17-2009, 10:17 PM
ok i went to kickers sight,i pulled one of their box construction manuals that give lenth width ect ect...i then went back to re calculator and put the exact demensions off of the kicker boxes and re was 2hz over.kickers demensions are with sub calculated into it.i dont know about re though.i will say that re helped me modify the length of my port and it sounds good.on my next box though,i would eliminate the back port completely for better airflow and more out put.if only my current box was 3" longer lol