4 12's in a Grand Prix

[MemphisCherokee]

So a buddy of mine with more money than brains wanted 4 PR's in his grand prix so i said i'd do it.
Pics:

http://img.photobucket.com/albums/v662/xunantar/DSCF5591.jpg

Sneak Peek of my new toy:
http://img.photobucket.com/albums/v662/xunantar/DSCF5592.jpg

More car audio:
http://img.photobucket.com/albums/v662/xunantar/DSCF5593.jpg

http://img.photobucket.com/albums/v662/xunantar/DSCF5595.jpg

http://img.photobucket.com/albums/v662/xunantar/DSCF5596.jpg

http://img.photobucket.com/albums/v662/xunantar/DSCF5597.jpg


My New Toy - Panel Pro Panel Saw
http://img.photobucket.com/albums/v662/xunantar/DSCF5603.jpg

http://img.photobucket.com/albums/v662/xunantar/DSCF5604.jpg

i just wish i could mount my 8.25 inch wormdrive skil saw on it.

Honestly, the install doesnt sound very great but he's satisfied. i wanna rip it out and do it again but those boxes aren't gonna come out unless theyre in atleast 3 pieces. and he's completely content.

[mazdakid]

it looks like you cut around the whole opening for the trunk

[bones22]

trunk is trashed

how much you give for the saw????

[MemphisCherokee]

it looks like you cut around the whole opening for the trunk

it does look that way
the kid i build it for had a box in fore that one that he didn't measure correctly for and had to bend it all. the paint got all chipped up and it rusted so it looks like i hacked the fvck out of it. he's the kind of kid that never sell's a car because he typically total's them so he doesn't care.

personally, i dont like having my work in a ****** vehical that's not taken care of but money is money at this point.

[MemphisCherokee]

trunk is trashed

how much you give for the saw????

it was only around 900-1000. atleast it wasnt 2200 like a milwaukee panel saw. it's acurate down to about 1/32 of an inch.

[bones22]

it was only around 900-1000. atleast it wasnt 2200 like a milwaukee panel saw. it's acurate down to about 1/32 of an inch.

not bad at all
can you rip with it to?

[MemphisCherokee]

not bad at all
can you rip with it to?

yeah, you turn the saw side ways and tighten that red clamp down at the measurment then run the sheet through it

edit: i ended up straightening out that flange that the trunk seal is on and repainting the rusted part after sanding it down. it's not perfect but it's gonna keep the water out.

[LDW3RD]

Nice little install.

Great looking panel saw. I want one!
Looks like a Bosch, is it?

[Dyme_a_Duzin]

Nice.

[LDW3RD]

Looks like the Ryobi from Rockler.
Also looks like it will fit in my garage nicely.:D
http://img.photobucket.com/albums/v662/xunantar/DSCF5604.jpg

[LDW3RD]

to much vodka

[99grandprixGT]

ya our trunk opening *****. i had to bend the medal around mine to get my box in.

[mazdakid]

ya our trunk opening *****. i had to bend the medal around mine to get my box in.

could have just built the box inside the trunk

[ThatChevyGuy]

You're friend has money eh?
Well then he wouldnt suffer too bad when someone jacks that amp.

[jbizzle]

Looks good

[audioarsonal]

The trunk appears to be missing the rubber gasket to seal it up?As for the panel saw....meh.More headache then its worth.
And with the box is it sealed?

[MemphisCherokee]

Nice little install.

Great looking panel saw. I want one!
Looks like a Bosch, is it?

it's a ryobi. i have yet to see how well it will cut through MDF but i'm excited to test it out.


The trunk appears to be missing the rubber gasket to seal it up?As for the panel saw....meh.More headache then its worth.
And with the box is it sealed?

We put the gasket back on after we straightened the opening out, sanded and painted it.

and no, the boxes are both ported into the cabin through the hole in theback seats each one is about 3.75 cf with around 70 square inches of port tuned to about 36 Hz. i never did get pics of the ports and whatnot.

[99grandprixGT]

could have just built the box inside the trunk

this was after the box was built. did not take account the trunk opening.

[thorshammer1]

Either way I love seeing a Grand Prix get loud!