PDA

View Full Version : Box build take 2!



darkhunter139
06-28-2008, 07:58 PM
Lol well some of you might have read my other thread, built a box and it did not fit in my trunk

This one is way better the pieces line up awesome and we cut it ourselves this time

Box is 31x18x15.75"

Its for a 15 inch SSD

Here are the pics what do you think this time :)

http://farm4.static.flickr.com/3175/2619787920_ae64708ce6.jpg

http://farm4.static.flickr.com/3046/2619788182_8085f54c22.jpg

http://farm4.static.flickr.com/3017/2619788438_c4ca58c5e9.jpg

This is my 3rd box build and I am improving each time. I did not screw up anything this time, the first time I messed up a whole side and it did not line up right but it still sounded good and I used it for a few months. Second time I drilled some extra holes in the top and bottom of the box and the back did not line up. (plus it didn't fit in my car lol)

bad_trip
06-28-2008, 08:01 PM
lol. congratulations. does this one fit for sure?

darkhunter139
06-28-2008, 08:02 PM
lol. congratulations. does this one fit for sure?

I measured and there is no reason this one shouldnt fit. Im still a little worried though.

Buck
06-28-2008, 08:02 PM
lets hope you can fit this one in there

hemi=22s
06-28-2008, 08:03 PM
lolz test fit beofre finishing build

bones22
06-28-2008, 08:03 PM
blade getting dull huh

looks good so far

darkhunter139
06-28-2008, 08:03 PM
lolz test fit beofre finishing build

Im going to text fit it after I silicone it and put the top on

darkhunter139
06-28-2008, 08:04 PM
blade getting dull huh

looks good so far


No I think its just that a few we had to leave right next to the blade before we could turn it off for a couple seconds so it just burned the sides


That piece right there has the worse burn mark out of all of them

darkhunter139
06-28-2008, 09:32 PM
How long do I need to wait for the glue to dry. The last two times I let it sit over night but I am itching to finish this. I dont want to jack it up though

miker
06-28-2008, 10:16 PM
How long do I need to wait for the glue to dry. The last two times I let it sit over night but I am itching to finish this. I dont want to jack it up though


I'll wait a couple hours usually.. Sets up really quick though.

darkhunter139
06-28-2008, 10:17 PM
its been about 2 hours already

PV Audio
06-28-2008, 11:59 PM
:laugh: I finish assembling and use it immediately. Never once had a problem.

kovemaster559
06-29-2008, 12:07 AM
make sure it fits

darkhunter139
06-29-2008, 12:35 AM
:laugh: I finish assembling and use it immediately. Never once had a problem.

Seriously? lol I will try it out tomorrow morning

Just going to silicone it up screw the top on, make sure the biotch fits then make the cut out

Im thinking I need bigger screws for the sub though, its 25 pounds and those screws I used on the box are kind of small.

Mattd0344
06-29-2008, 11:08 AM
What is your box tuned to? and what are the dimensions to your port pieces???

darkhunter139
06-29-2008, 11:35 AM
Its tuned to like 32.5

I wanted to tune it to 33 but then I would have had to make a weird cut so I figured I would just do it this way. I wont be able to tell a differnce.

The port width 3 port lenth 2 8

I used this

http://reaudio.com/speaker_box/LPort_Box_Calc.html

Want a screen shot of the plans?

I just put the lid on today, its looking good

BobbyDD
06-29-2008, 01:36 PM
The only thing I see wrong is that you're way too close to the corners with the screws. Good job if it fits though.

dumpin907
06-29-2008, 01:43 PM
you should put 45's in the corners

darkhunter139
06-29-2008, 01:45 PM
The only thing I see wrong is that you're way too close to the corners with the screws. Good job if it fits though.

Ahh so its not good to get that close? They didnt split so its all good.


What are 45s and what is the purpose of that?

darkhunter139
06-29-2008, 05:56 PM
Victory!!!!!!

http://farm4.static.flickr.com/3285/2621868777_ebd1d53475.jpg