PDA

View Full Version : retard builder

04-07-2008, 10:59 AM
I need help building this box. Because i dont understand

Use 3/4" material to build your box

Make your box with the following internal dimensions: W=32" H=13"
D=12.5"

Fire the subs and port to the rear. You will have a slot port; use
either end of the box end panels for the outer port wall. Center your
subs in the area between the inner port wall and the opposite end of
the
box.

Your port will be 3." wide and 13" tall and 20" long (measured from the
outer face of the box)You will have to bend the port 90 degrees at a
point 3" from the inside face of the rear box panel and continue the
inner port wall for a distance of 10.5"

Your port opening area will be 40 sq" and be tuned to approx 37 Hz

Your box will be 2.5 cubes net after displacements

Have fun

dj

I dont understand it.. is it literally for sides and then on one side a port cut out? on the same side as the subs? I dont understand how it could be both tall wide and long it just doesn't make sense. Help a brother out

mlstrass
04-07-2008, 11:43 AM
Instructions for a slot ported box, makes sense to me....

loudmofo
04-07-2008, 11:43 AM
me 2

BobbyDD
04-07-2008, 11:46 AM
I understand the box but I don't understand your question.

The box is designed to look like this, you can put the port on either end...

http://i19.ebayimg.com/04/i/08/bb/54/d3_1.JPG

04-07-2008, 01:01 PM
Ohhhh okay but how do i know how to make the bend and how far to go with that bend inside the box?

ThatChevyGuy
04-07-2008, 01:01 PM
use reaudio.com calculator
more visual perspective

04-07-2008, 01:06 PM
thanks a lot everyone

BobbyDD
04-07-2008, 01:36 PM
Ohhhh okay but how do i know how to make the bend and how far to go with that bend inside the box?

You will have to bend the port 90 degrees at a
point 3" from the inside face of the rear box panel and continue the
inner port wall for a distance of 10.5"

Taken from your first post...

Immacomputer
04-07-2008, 01:47 PM
http://i27.tinypic.com/vpylhh.png

That's what he is describing. I disagree that it's tuned to 37hz though. It's much closer to 40hz and about 2.35 net after sub displacement. It's 2.48 cubes before the subs are in it but after the port.

04-07-2008, 07:53 PM
http://i27.tinypic.com/vpylhh.png

That's what he is describing. I disagree that it's tuned to 37hz though. It's much closer to 40hz and about 2.35 net after sub displacement. It's 2.48 cubes before the subs are in it but after the port.

i almost feel like i have to pay you for that post. Thank you so much my friend!

GnFnRs
04-08-2008, 06:25 PM
am i looking at the pic wrong or am i just stupid? lmao
the port is supposed to be 20" long. is it measured from the center of the bend or the inner bend?

really a ******* question but i never had to bend a port before.

Immacomputer
04-08-2008, 06:35 PM
Center of the bend. I think I interpreted DJ's directions wrong. My drawing shows a 20" long port length but DJ mentions a 10.25" piece. I assume that is supposed to be where the 6" piece is. If that is the case, the enclosure gets even smaller.

GnFnRs
04-08-2008, 06:45 PM
thats what i thought it was but never done it. and i am guessing i'm about to have to lol