PDA

View Full Version : Box design for L7



BassHead99
02-19-2008, 05:51 PM
Im wanting about 3ft^3, and around 34hz or so. Its for a single L7 and space isnt an issue, I have plenty of room to work with. Can anybody help me out?

Atimm693
02-19-2008, 06:43 PM
Sure.

Subs up port back im assuming?

12 inch?

Atimm693
02-19-2008, 07:31 PM
Here you go. Specs are 3.2ft^3@34htz. 3 inch port 22" long.
Cuts:
Top and Bottom: 31.5x 18.5
Back: 31.5x 13
Front: 29.75x 13
Left Side: 17.75x 13
Right side: 17x 13
Port 1: 13.25x 13
Port 2: 7.25x 13

Pics:
http://i140.photobucket.com/albums/r27/cheechy___chong/ghjkghj.jpg
http://i140.photobucket.com/albums/r27/cheechy___chong/ghjgjgh.jpg

Lakota
02-19-2008, 10:09 PM
Here you go. Specs are 3.2ft^3@34htz. 3 inch port 22" long.
Cuts:
Top and Bottom: 31.5x 18.5
Back: 31.5x 13
Front: 29.75x 13
Left Side: 17.75x 13
Right side: 17x 13
Port 1: 13.25x 13
Port 2: 7.25x 13

Pics:
http://i140.photobucket.com/albums/r27/cheechy___chong/ghjkghj.jpg
http://i140.photobucket.com/albums/r27/cheechy___chong/ghjgjgh.jpg

That was pretty **** generous of you.

BrianChia
02-19-2008, 10:23 PM
It was very nice of you to do the design. Not trying to be rude but the port length is actually measured as 27.25" (you measure down the center of the port and add 1/2*width for "end correction"). It will lower the tuning (probably around 30hz) but its not a really big deal.

Atimm693
02-19-2008, 10:26 PM
That was pretty **** generous of you.

Tonight i was bored as hell, not to mention im doing this for experience and practice. Im also trying to get my rep up before i start to charge people.

BassHead99
02-19-2008, 10:45 PM
Tonight i was bored as hell, not to mention im doing this for experience and practice. Im also trying to get my rep up before i start to charge people.

That was very generous of you. I dont want to sound like a d*** but i actually have two and im getting one fixed (broken tensil lead). Do you think you could play around with a design for two 12"s? Same freq. just double the volume. If you could that would be awesome. Thanks again man!

Atimm693
02-19-2008, 10:48 PM
That was very generous of you. I dont want to sound like a d*** but i actually have two and im getting one fixed (broken tensil lead). Do you think you could play around with a design for two 12"s? Same freq. just double the volume. If you could that would be awesome. Thanks again man!

Tomorrow afternoon ill get right on it. :)

BassHead99
02-19-2008, 10:50 PM
Tomorrow afternoon ill get right on it. :)

Thanks again. So what was the port length supposed to be? Is it 27.25"?

BrianChia
02-19-2008, 10:54 PM
I got 27.25" of port at 3.36 cf net. If the net displacement is 3.2 assuming 0.16 for the sub, it should tune to 29 hz.

Atimm693
02-19-2008, 11:02 PM
Port should be 22" long.

Atimm693
02-19-2008, 11:08 PM
****, just realized i measured the port wrong. Knock 1.5" of the second panel of the port to fix it. So it should be 5.75x 13.

BrianChia
02-19-2008, 11:14 PM
Measure down the line through the center of the port, adding 1/2*port width at the end if using the wall of the box as a side of the port.

http://img519.imageshack.us/img519/6389/portlengthyd0.png

Atimm693
02-20-2008, 05:43 PM
Lol i missed your little post above. WiniSD said that i needed 22" of port to tune to 34 htz. Also thanks for correcting me and for the 1/2" tip. :)

OP im working on the design for both now, ill PM you when finished.

vetkilr
02-20-2008, 05:45 PM
You need to have at least 40 sq of port.....50 if you like it low and loud.

fbi90909
02-20-2008, 05:49 PM
a little off topic but how do you get the arrows and lenghts to show up when using sketchup?

Atimm693
02-20-2008, 06:23 PM
something like advanced toolbox in tools, then its right below the tape measure

fbi90909
02-20-2008, 06:32 PM
took a minute but thanks!