PDA

View Full Version : PG Rsd6.5 @ 2 Ohms.



Gilliz
12-10-2007, 10:18 PM
I'll damage my ish yes? If I go Higher say 8, It'll be ok no?

Thx.

tcguy85
12-10-2007, 11:06 PM
what are you talking about?

jblayz1
12-10-2007, 11:08 PM
hahahaha :laugh:

IonSQL
12-10-2007, 11:09 PM
ummm, yeah.......

BASS_WARRIOR
12-10-2007, 11:09 PM
lol I was wondering the same thing

dragnix
12-10-2007, 11:10 PM
wow...just wow

IonSQL
12-10-2007, 11:12 PM
Whatever you do, just don't run them at 4 ohms, and you'll be fine... :fyi:

tcguy85
12-10-2007, 11:13 PM
run them at 0.5 ohms!

not sure how..... but make it work.

Troydb
12-10-2007, 11:53 PM
you need four amps.. one for each speaker.

Towncar
12-11-2007, 03:26 AM
hmm

fwb_1234
12-11-2007, 03:32 AM
I'll damage my ish yes? If I go Higher say 8, It'll be ok no?

Thx.

Rewrite your question, ignore them, and then I'll try to help.

mdillon
12-11-2007, 08:38 AM
I'll damage my ish yes? If I go Higher say 8, It'll be ok no?

translated to:

if i run my components at 2 ohms will i damage them? but if i run them higher, up to 8 ohms will they still run fine?

i hope im right....

IonSQL
12-11-2007, 08:41 AM
Yeah, I think we knew what me meant.... doesn't change anything

Etac
12-11-2007, 10:49 AM
the speaker doesnt care what resistance it has...if you wired a pair down to 2 ohms (which is the only way i see how) it should be fine as long as your amp can handle it and you dont put too much power into them.. but if you're wiring one set down to 2 ohms.. dont forget it will be mono..

J31Rob
12-11-2007, 10:56 AM
I'll damage my ish yes? If I go Higher say 8, It'll be ok no?

Thx.

Only difference is more/less power, 2 ohm = more, 8 ohm = less.


Rewrite your question, ignore them, and then I'll try to help.

Yeah, some people just can't use common sense to make sense of an apparently miswritten statement.


I'll damage my ish yes? If I go Higher say 8, It'll be ok no?

translated to:

if i run my components at 2 ohms will i damage them? but if i run them higher, up to 8 ohms will they still run fine?

i hope im right....

Refer to my first reply.

IonSQL
12-11-2007, 11:57 AM
Someone want to explain how he's going to run his 4-ohm components at anything other than 4 ohms????

tapout
12-11-2007, 12:01 PM
Someone want to explain how he's going to run his 4-ohm components at anything other than 4 ohms????

duh, j00 gotta run dem bishes in "sooper dooper series parallelogram"

Etac
12-11-2007, 12:06 PM
duh, j00 gotta run dem bishes in "sooper dooper series parallelogram"

ftw

i could see if you had two pairs this would seem logical i guess...

JimJ
12-11-2007, 12:07 PM
Two pairs per channel is going to be some hideous sound.