PDA

View Full Version : Wiring 4 ohm and 6 ohm together??



97JeepTJ
02-27-2007, 05:09 PM
Are there any problems with wiring a 4 ohm speaker and a 6 ohm speaker together (I assume this becomes a 3 ohm load)???

btlking
02-27-2007, 05:10 PM
i dont think your suppose to mix voice coils

fatryan
02-27-2007, 05:14 PM
depends how u wire it...

parallel: (1/Req)= (1/R1) + (1/R2) = (1/4) + (1/6)
Req= 2.4ohms
Series: Req = R1 + R2 = 4 + 6
Req= 10ohms

97JeepTJ
02-27-2007, 05:17 PM
im going with parallel ... but the real question is there anything wrong with wiring these 2 different speakers together?

fatryan
02-27-2007, 05:19 PM
well it kinds depends. i wouldnt recommend it for regular speakers, but it should be fine for subs. you just need to understand how the power is detributed and how much they can handle

fatryan
02-27-2007, 05:31 PM
Im bringin back old general physics knowledge here, so be advised, there may be mistakes ha ha...

P=(V^2/R)

now the Voltage across all resistors in a PARALLEL circuit (not series) is the same. So the variable is the Resistance. so you got a 4ohm and 6ohm resistor...

P1= (V^2/4ohm)
P2= (V^2/6ohm)

compare to ratings, if they dont exceed RMS power handling, you should be set

Gary S
02-27-2007, 11:09 PM
i dont think your suppose to mix voice coils



- That's an old myth. Total ohm load will be less than 4 ohms. The 4 - ohm speaker will get a little more power than the other. other than that, it will work just fine.

blackbonnie
02-27-2007, 11:17 PM
the power will not be distributed evenly, even if they handle the same power load current takes the path of least resistence so your 4 ohm speaker would get more, in return would probably have one speaker drown out the other. Wouldnt be recomended, i say seperate the subs. what does everyone else say?

///M5
02-27-2007, 11:21 PM
You can do it, but it won't sound good.

97JeepTJ
02-28-2007, 12:29 AM
They arent subs ... Eclipse 6.5" coaxials (fronts @ 4 ohm) and these random 6.5" mid-bass/woofers (back @ 6 ohm).

I'll see how it sounds. Its not a permanent thing so its not a big deal if sound is perfect. I just want to get the speakers louder and clearer.

///M5
02-28-2007, 12:47 AM
Back speakers are retarded and wiring them that way would be even worse. If you want it to sound "clearer" that isn't going to help at all.

fatryan
02-28-2007, 02:14 AM
They arent subs ... Eclipse 6.5" coaxials (fronts @ 4 ohm) and these random 6.5" mid-bass/woofers (back @ 6 ohm).

I'll see how it sounds. Its not a permanent thing so its not a big deal if sound is perfect. I just want to get the speakers louder and clearer.def dont do it

DaveDSMer
02-28-2007, 03:23 AM
you would lose all ability to fade your music front or rear.. just to give you the heads up.

blackbonnie
02-28-2007, 10:05 AM
why would ou wire you fronts and backs together anyway, run fronts of HU and then backs of a little 200 w amp and ou wont even have to worry about 4 and 6 ohm. just dont wire them together.

JimJ
02-28-2007, 10:14 AM
run fronts of HU and then backs of a little 200 w amp

Did you mean the other way around? :)

97JeepTJ
02-28-2007, 10:23 AM
Im not worried about fading right now (I probably will when the speakers are amped though, lol). The only reason I want the backs amped with the fronts is because of the mid-bass driver. It doesn't get loud enough off HU power as it sits now. The eclipse's really have no low end umph (I know they're not really made for that purpose), so i wanted those to act more like high frequency mid-bass with a side of tweet. Either way, I'll probably wire the speakers both ways to see what I like better.

blackbonnie
02-28-2007, 09:12 PM
yeah i did, sorry my bad. ^^^