PDA

View Full Version : Box Build ----Fiberglass & MDF



dbornotdb
02-12-2007, 12:45 AM
I'll just start with all the pics and the captions with them.
Just a copy and paste from another forum I have it posted on.

Calikid
02-12-2007, 12:45 AM
is that forum fiberglassforums.com

dbornotdb
02-12-2007, 12:47 AM
It is in a 99 s10.

Here are the back half of the box pics. This is the part that will be in the bed.









http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_braced_1.jpg

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_braced_2.jpg

dbornotdb
02-12-2007, 12:48 AM
is that forum fiberglassforums.com




It is.

You familiar with the build?

dbornotdb
02-12-2007, 12:49 AM
Resined it for a waterproof finish.
This is just the inside, the outside was done also.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_resined_1.jpg

dbornotdb
02-12-2007, 12:50 AM
A shot of the back wall looking through the blow-thru at the new back half of the box.
Never mind the mess........will be cleaned before it is done.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_new_blow_thru_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_new_blow_thru_2.JPG

dbornotdb
02-12-2007, 12:52 AM
The notch here is for the console...and some style points.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_console_radius.JPG





And todays radius' are brought to us by this half used roll of tape.




http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_tape_radius.JPG

dbornotdb
02-12-2007, 12:54 AM
Working the floor and that ugly step.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_start_of_floor_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_start_of_floor_2.JPG

dbornotdb
02-12-2007, 12:54 AM
Throw some braces on it and test the box connector to the bed part of the box.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_back_braced.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_connector_test.JPG

dbornotdb
02-12-2007, 12:56 AM
When I left off, I had the connector pieces sides built and test fitted.
Well here are the pics of it all done with the mounting flanges built on each side so it can be connected.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_connector_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_connector_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_connector_3.JPG

dbornotdb
02-12-2007, 12:56 AM
The inside flange is where it will be bolted to the bed part of the box and the outer flange will attach it to the inside part of the box.

Here is the test fit of it all done before I put Everglass on the seams to reinforce it.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_connector_done.JPG

stuckinok
02-12-2007, 12:57 AM
looking real good man iam a fan of your work on fiberglassforums.com

dbornotdb
02-12-2007, 12:57 AM
I dislike the dowl method of setting up rings. I only use it if I can't use a 2x4.

I get asked how to use a 2x4 like this and when I explain it, they get lost. Maybe these pics will help.

I cut the 2x4 at the angle I want the ring to sit and attach them together with 1 screw in the center where the pivot was for the router.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_rings_on_2x4.JPG

dbornotdb
02-12-2007, 12:59 AM
Position the ring at the angle you want it and shoot some paint around the base of it.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_set_and_painted_1.JPG






This will mark the position of the 2x4. You will trace this position next.




http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_set_and_painted_2.JPG

dbornotdb
02-12-2007, 12:59 AM
looking real good man iam a fan of your work on fiberglassforums.com




Thanks.

Flipx99
02-12-2007, 12:59 AM
****, I was hoping for an s-10 inside the extended can build...


**** good job either way.

dbornotdb
02-12-2007, 01:00 AM
Grab you a piece of paper or posterboard and cut it to the edges of the wood and where the 2x4 was marked at.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_2x4_template_1.JPG




Now flip it to the other side and trace the position of the 2x4.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_2x4_template_2.JPG






Should be a perfect image of the other side.
Drill 2 pilot holes so you can secure the 2x4 from underneath and your good to go.




http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_2x4_template_3.JPG





This will allow you to cut the center of the ring out, remove the 2 screws from underneath and it will lift out.

dbornotdb
02-12-2007, 01:00 AM
****, I was hoping for an s-10 inside the extended can build...


**** good job either way.



Keep reading, it is coming.

j3bus2k3
02-12-2007, 01:01 AM
Nice work so far man...You never left me your number :) I'll probably be around friday or wednesday depending on a few things...

dbornotdb
02-12-2007, 01:02 AM
As you might have noticed, the center of my rings are still attached. I routered about 3/4 of the way through and when I am ready, I will follow that groove with an air saw. Keeps the insides clean with no tape waste.




Here is a shot of the rings placed and the port set in the center to see how it would look.
Looked good to me.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_rings_set.JPG

dbornotdb
02-12-2007, 01:03 AM
Nice work so far man...You never left me your number :) I'll probably be around friday or wednesday depending on a few things...



I'll PM you my number as soon as I finish this thread.

j3bus2k3
02-12-2007, 01:04 AM
I'll PM you my number as soon as I finish this thread.

No rush:)

dbornotdb
02-12-2007, 01:09 AM
I glued the connector piece in and sealed and reinforced all the seams.







http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_reinforcing_joints.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_profile_before_stretch.JPG




How the connector looks installed and the edges rounded over.




http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_ready_for_material_1.JPG

dbornotdb
02-12-2007, 01:10 AM
Now we are getting somewhere.

Installed the port and the top. Getting closer to stretching this thing.







http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_ready_for_material_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_ready_for_material_3.JPG[/COLOR]

Calikid
02-12-2007, 01:11 AM
It is.

You familiar with the build?

yep, looks good :D

dbornotdb
02-12-2007, 01:11 AM
We have all heard the rumours and tall tales about painting the ports to get dB's right?

Well one tale that doesn't circulate alot, because those that know want to keep it hush hush, is the Butterflies make BASS












http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_butterflies_for_bass.JPG

dbornotdb
02-12-2007, 01:12 AM
When I found a polydex material with butterfly beads on it, there was no way I could pass that up. So I bought all 8 yards they had.




I know.............your jealous.

Flipx99
02-12-2007, 01:14 AM
I have a question...what do you use to make the router go straight. I have the hardest time with the first part of a roundover. In the middle I do okay...it's just the starting that kills me. I am thinking of plunging in the middle and going out.

PowerNaudio
02-12-2007, 01:16 AM
sick work bro, looking forward to the rest of the build.

dbornotdb
02-12-2007, 01:18 AM
Stretched the material over the thing.
Wasn't as bad as I thought it would be, but that could have been cause I had an extra set of hands helping me.










http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_stretched_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_stretched_2.JPG



And a shot from the rear looking through the box connector piece.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_stretched_3_rear.JPG

dbornotdb
02-12-2007, 01:21 AM
I have a question...what do you use to make the router go straight. I have the hardest time with the first part of a roundover. In the middle I do okay...it's just the starting that kills me. I am thinking of plunging in the middle and going out.



Not exactly sure of your problem.

Are you moving the router counter-clockwise?

dbornotdb
02-12-2007, 01:23 AM
Resined up, Everglass applied to the exterior and all the strengthening of the box was done on the inside to minimized the body work needed.










http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_resined_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_resined_2.JPG

dbornotdb
02-12-2007, 01:25 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_everglass_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_everglass_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_everglass_3.JPG

dbornotdb
02-12-2007, 01:25 AM
Took an angle grinder with a flap disc to the Everglass. Makes quick work of it.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_grinding_outside.JPG



http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_new_avatar.JPG

dbornotdb
02-12-2007, 01:27 AM
Now you are up to date on the box.




If you want to see the rest of the truck build, see it here....

http://www.fiberglassforums.com/showthread.php?t=1587

kickerlivinloud
02-12-2007, 03:55 PM
Wow, you deffently have my respect when it comes to the build!!! Looks amazing!!!!!!





Jon

acold7dusta
02-12-2007, 05:09 PM
Wow, you deffently have my respect when it comes to the build!!! Looks amazing!!!!!!





Jon


:word:

azbass
02-12-2007, 05:13 PM
When I found a polydex material with butterfly beads on it, there was no way I could pass that up. So I bought all 8 yards they had.




I know.............your jealous.

a true fiberglasser knows. butterflys and crap make the box sound better :)

azbass
02-12-2007, 05:13 PM
box looks kick ***. and i even learned a thing or two.

OneKrazyKeebler
02-13-2007, 01:12 AM
Nice work bro!

I might have a few questions for you when I start my build.

dbornotdb
02-13-2007, 02:04 AM
Thanks everyone.

I made the amp rack today, but that is all.
It is on the fiberglass forums link.
I should be sanding this box out tomorrow.

dbornotdb
02-15-2007, 12:07 AM
Sanded the box.


Then a layer of Rage went on.
Sanded that.

Then did another layer of Rage.

Will sand that off tomorrow. Fix anything the Slick Sand won't fill and then primer.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_body_filler_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_body_filler_2.JPG

dbornotdb
02-20-2007, 11:45 PM
Sanded that down with some 36 grit and circle the bad low spots.

There were alot.






http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_bad_spots.JPG



And fill them in.





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_touch_up_filler.JPG

dbornotdb
02-20-2007, 11:46 PM
Before I do any primering on it, I test fit it to make sure it is all good and goes as planned.

Slid it in and it went right in where it was suppose to go. Good luck or good planning?


Here are a couple shots of the flange on the inside where the bed part of the box and the cab part are bolted together.







http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_inside_flange_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_inside_flange_2.JPG

dbornotdb
02-20-2007, 11:47 PM
Box in and amp rack going in so I cen test listen over the weekend.
It was too cold for primering it anyways.








http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_test_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_test_2.JPG

~Magick_Man~
02-21-2007, 05:08 AM
did you not add any additional layers of glass after the polydex?
it looks like you did that then went straight to the filler.
i am only asking because in the second to last pic with it in the truck i can see the butterflies on the inside of the enclosure.


but it still kicks ***.

~Magick_Man~

dbornotdb
02-21-2007, 09:44 AM
did you not add any additional layers of glass after the polydex?
it looks like you did that then went straight to the filler.
i am only asking because in the second to last pic with it in the truck i can see the butterflies on the inside of the enclosure.


but it still kicks ***.

~Magick_Man~





Post #32.....................



Everglass applied to the exterior and all the strengthening of the box was done on the inside to minimized the body work needed.




A couple layers of mat and then a mixture of cabosil, thixotropic, talc and saw dust that I came up with to make it thick. It adds weight, but the fiberglassed part is more solid than the MDF parts.

dbornotdb
02-22-2007, 09:50 PM
Layed some primer today and then sanded it to get it as smooth as possible. I will lay some more primer tomorrow and this time I will remember to bring the camera.

I will also get pics of the inside of the so you can see the strengthening of it.

j3bus2k3
02-22-2007, 09:54 PM
did you get my PM??

dbornotdb
02-22-2007, 09:58 PM
did you get my PM??




Sure did.
I will be looking for a package from Brown Santa on Monday.

j3bus2k3
02-22-2007, 10:19 PM
Sure did.
I will be looking for a package from Brown Santa on Monday.

Awesome...santa hasn't arrived for me, a little over a 3-weeks late. I think he zigged when he should have zagged tryin to find my house :crap:

mobeious
02-22-2007, 10:26 PM
hmmm dont know bout this... doesnt look like that good of a box design..... why not just do a full blow through?

LvnLoud
02-22-2007, 10:34 PM
I'm confused as to what I've just seen.

mobeious
02-22-2007, 10:49 PM
blowthrough = Subs in bed in a box "blown through" into the cab

dbornotdb
02-22-2007, 11:36 PM
blowthrough = Subs in bed in a box "blown through" into the cab




I know what a blow-thru is. I have done about 12 in my time.

The old set-up was a blow-thru, but since some subs were lost due to theives and then 2 more have bad popping issues, I decided to use the bed for airspace and build something fancy like in the cab. After the math with the subs, they need alot of airspace. They are some old MA 15IL series. 6.5 per sub.


This truck lives in Lakeland. Southside. Maybe you will see/hear it around. Should be going back this weekend.

mobeious
02-22-2007, 11:50 PM
tell him to stop by our show this weekend at our shop in winterhaven, bout 5miles from lakeland.. and ill let him hear a real blow through

dbornotdb
02-23-2007, 12:02 AM
tell him to stop by our show this weekend at our shop in winterhaven, bout 5miles from lakeland.. and ill let him hear a real blow through




So what is your problem?

Kenny Pollock
02-23-2007, 12:32 AM
mobeious: how is this not a real blow through?

I've heard it in person (when the subs were under powered and with subs not 100% working) and it sounded bad ***.

baseballer1100
02-23-2007, 01:28 AM
nice.

mobeious
02-23-2007, 08:15 AM
ok im not bashin the dude its just its not a blow through... its a box.... if it sounds good thats all that matters... from the first pics it just didnt look like it was going to perform to well.... but if it beats.. props to ya

helotaxi
02-23-2007, 01:22 PM
ok im not bashin the dude its just its not a blow through
You're right, it's a cut through. So what?

dbornotdb
02-24-2007, 02:10 AM
You may have noticed I didn't lay mat on the exterior of the box.

I did a couple layers on the inside and used this special mixture of thixotropic/resin mix.

You can see how thick it is at the ring. It is more solid than the MDF is.




http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_interior_strength.JPG

dbornotdb
02-24-2007, 02:10 AM
Here are some of the primer on it and drying.








http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_primered_box_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_primered_box_2.JPG

j3bus2k3
02-24-2007, 02:32 AM
NICE!

BTW...If I cant wrap my doors in my vinyl...can I bring them to you :)

kaimana
02-24-2007, 05:10 AM
Looks awesome!!!!! Man thats a lot of work...well worth it though...


ps...i thought i was the only one with ma audio...lol....props on that...

dbornotdb
02-24-2007, 12:16 PM
NICE!

BTW...If I cant wrap my doors in my vinyl...can I bring them to you :)






That can be a possiblility.







And thanks for the comments everyone.

Trey803
02-24-2007, 12:23 PM
How did you measure the volume of the fiberglassed part of the box?

dbornotdb
02-25-2007, 10:39 AM
How did you measure the volume of the fiberglassed part of the box?




Packing peanuts.

Tape off the inside part of the port.
Tape off the subs mounting holes.
Pour peanuts inside the box thru the opening i have in the rear till full.
Epty peanuts into a box and measure the width, depth and heigth of them inside the box.
Calculate.
Subtract the subs displacments.

In my case--- .85 cuft

MemphisCherokee
02-25-2007, 11:20 AM
hahaha, if you put the subs on upside down, the whole enclosure would look like a pair of ****
great ****ing work though

holy ****, please delete some of those

MemphisCherokee
02-25-2007, 11:20 AM
hahaha, if you put the subs on upside down, the whole enclosure would look like a pair of ****
great ****ing work though

baseballer1100
02-25-2007, 11:43 AM
Thats amazing.

dbornotdb
02-27-2007, 11:38 AM
Thanks guys.

Here are ALOT of pics.

dbornotdb
02-27-2007, 11:42 AM
Wet sanding the primer...








http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_wet_sand_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_wet_sand_2.JPG




Smoooooooth





http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_wet_sand_3.JPG

dbornotdb
02-27-2007, 11:43 AM
The base coat. Silver Metalflake.







http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_base_coat_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_base_coat_1.JPG

dbornotdb
02-27-2007, 11:43 AM
Clear coat.







http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_clear_coat_1.JPG

dbornotdb
02-27-2007, 11:44 AM
Starting the final install.









http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_mid_install_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_mid_install_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_mid_install_3.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_mid_install_4.JPG

dbornotdb
02-27-2007, 11:44 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_console_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_console_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_box_in_1.JPG

dbornotdb
02-27-2007, 11:45 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_truck_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_truck_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_truck_3.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_truck_5.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_truck_4.JPG

dbornotdb
02-27-2007, 11:45 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_bed_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_bed_1.JPG

dbornotdb
02-27-2007, 11:46 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_interior_1.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_interior_3.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_interior_2.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_02.JPG

dbornotdb
02-27-2007, 11:46 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_01.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_05.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_04.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_03.JPG

dbornotdb
02-27-2007, 11:47 AM
http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_07.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_08.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_09.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_10.JPG

http://epicenterdesigns.com/photo-gallery/albums/userpics/10001/normal_SOM_06.JPG

dbornotdb
02-27-2007, 01:06 PM
http://i21.photobucket.com/albums/b261/dbornotdb/th_99s10fiberglasssedbox.jpg (http://s21.photobucket.com/albums/b261/dbornotdb/?action=view&current=99s10fiberglasssedbox.flv)

jmanpc
02-27-2007, 01:16 PM
got numbers?

dbornotdb
02-27-2007, 01:25 PM
got numbers?




No numbers.
And to not sound like an ***, I won't say that by ear, it sounds like it could be a 143 -144.

kickerlivinloud
02-27-2007, 01:35 PM
Your work is freaken impressive man!!! I'd love you have your glassing skills!




A++++++


Jon

LUV2BHATED
02-27-2007, 01:42 PM
very nice and impressive db, ill even let you know that in the other forum :D

saj21187
02-27-2007, 01:57 PM
nice *** work there man, too bad your a long way from me or i might have you do some glass work for me. Did you do the dash and everything in that car or just the stereo?

dbornotdb
02-27-2007, 02:39 PM
nice *** work there man, too bad your a long way from me or i might have you do some glass work for me. Did you do the dash and everything in that car or just the stereo?





I do ALOT of mail order jobs.
I am doing a dash and other peices for a guy in NY and another fiberglassed dash for a guy in Canada soon.

I did the whole truck. There is a link to the whole truck build at the beginning of this thread.

saj21187
02-28-2007, 12:40 AM
I do ALOT of mail order jobs.
I am doing a dash and other peices for a guy in NY and another fiberglassed dash for a guy in Canada soon.

I did the whole truck. There is a link to the whole truck build at the beginning of this thread.

Just out of curiousity what do you usually charge for glass work? I know it would be hard to say exactly but just like a rough estimate to do some light work on a dash. Im getting a 2007 toyota tundra before summer, and am still thinking about what i want to do with it audio wise. I already have all the equipment, the main thing im worried about is if i will have to do some custom work to the dash to get my eclipse double din to fit in it correctly. Do you do any home audio stuff or strictly car audio.

dbornotdb
02-28-2007, 10:03 AM
Just out of curiousity what do you usually charge for glass work? I know it would be hard to say exactly but just like a rough estimate to do some light work on a dash. Im getting a 2007 toyota tundra before summer, and am still thinking about what i want to do with it audio wise. I already have all the equipment, the main thing im worried about is if i will have to do some custom work to the dash to get my eclipse double din to fit in it correctly. Do you do any home audio stuff or strictly car audio.




If it is cutting and molding a double din in, starts around $200 + shipping.
You want it textured and color matched back? Thats more.
Want it smoothed out and primed so you can paint it? Thats more.
I do alittle bit of everything.

mazdakid
02-28-2007, 06:15 PM
do the subs really see the full volume of the box since the opening to the bed is so small?

dbornotdb
03-01-2007, 01:14 AM
do the subs really see the full volume of the box since the opening to the bed is so small?



Absolutly.
The opening into the bed is bigger than it appears in the pics.

NhustlaR
03-01-2007, 01:27 AM
yeah, that is a very weirdly designed box, but im glad it works for ya!

ngsm13
03-01-2007, 01:51 AM
Sweet work, as always!

nG

2kchevy06civic
03-01-2007, 01:58 AM
looks bad ***.