View Full Version : Need help with calculations from Ported box Sticky

ultimate157

02-06-2007, 02:24 PM

Vd = Sd x Xmax (Where Sd = surface area of cone?)

Sd = 3.372^2 * 3.14 = 35.76

Xmax = 0.45 inches

Vd = 35.76 * 0.45 = 16.092

Now, as soon as I try to calculate required port area, with tuning of 35hz

dV>/= 39.37*(Fb*Vd)^0.5

dV = 39.37 * (35*16.092) ^ 0.5

= 39.37 * 23.73

= 934 sq inches of port area ??

berserker

02-06-2007, 03:54 PM

Fi SSD12 used for reference.

Vd = Sd*Xmax

Vd = Sd (M^2) * Xmax (Meters)

Vd = 0.048 * 0.021

Vd = 0.001008

dV >/ 39.37*(Fb*Vd)^0.5

dV >/ 39.37 * (Fb*Vd)^0.5

dV >/ 39.37 * (35*0.001008)^0.5

dV >/ 39.37 * 1.878297101

dV >/ 7.394855687

dV >/ 7.39

A = Pi*R^2

A = Pi * R^2

A = 3.142 * 3.695^2

A = 42.89870455

A = 42.90

And you end up with 42.90 In^2 minimum vent area with tuning of 35 Hz.

ultimate157

02-06-2007, 03:59 PM

Ahh ... thank you. I didn't see anywhere in the sticky that said what units to put them in.

berserker

02-06-2007, 04:01 PM

You are welcome and I believe it doesn’t from what I have seen skimming through it just before doing this for you.

ultimate157

02-06-2007, 04:27 PM

You are welcome and I believe it doesn’t from what I have seen skimming through it just before doing this for you.

Lv = [(1.463*10^7R^2)/(Fb^2*Vb)] - 1.463

How about this equation ... 1.463x10^(7R^2) ..... comes out to be a number to the 40th power.

BTW: Numbers I'm using are:

for a TS/W106DVC Pioneer Premier. Have it laying around and I want to build a ported box for it.

Fs 35.4

Qms 10.46

Qes 0.52

Qts 0.5

Vas 0.955

Rms 2.453

Mms 115.49

Cms 1.8x10-4

Diam 7.9in

BL 17.62 (8Ohm)

8.81 (2Ohm)

Xmax .45in 11.5 MM (0.0115 meters)

slikrider20

02-06-2007, 04:42 PM

Fi SSD12 used for reference.

Vd = Sd*Xmax

Vd = Sd (M^2) * Xmax (Meters)

Vd = 0.048 * 0.021

Vd = 0.001008

dV >/ 39.37*(Fb*Vd)^0.5

dV >/ 39.37 * (Fb*Vd)^0.5

dV >/ 39.37 * (35*0.001008)^0.5

dV >/ 39.37 * 1.878297101

dV >/ 7.394855687

dV >/ 7.39

A = Pi*R^2

A = Pi * R^2

A = 3.142 * 3.695^2

A = 42.89870455

A = 42.90

And you end up with 42.90 In^2 minimum vent area with tuning of 35 Hz.

Where did you get 3.695 from?

ultimate157

02-06-2007, 04:45 PM

Where did you get 3.695 from?

dV is the required port diameter. R = 1/2 of the diameter. 1/2 of 7.39 = 3.695

slikrider20

02-06-2007, 04:56 PM

Required port diameter?

ultimate157

02-06-2007, 11:24 PM

bump ... anyone have an answer to my 2nd question ?