PDA

View Full Version : Anyone need a 3D sketchup done of a box ? im bored



Pages : [1] 2

mobeious
11-14-2006, 08:54 PM
as title says

Jared530
11-14-2006, 09:11 PM
i do. i want to build a new box. My edges arnt flush and i get alot of port noise. arggh
95 honda accord
15 XXX
go at it

squeak12
11-14-2006, 09:15 PM
If your port edges aren't flush with the baffle, get someone to run a router with a flush bit on it.

Jared530
11-14-2006, 09:19 PM
Well pretty much all the edges arnt flush. and they are so wavy that youll probably have to take another inch off the top. I just want to design another box.

vetkilr
11-14-2006, 09:26 PM
15" sub

32 W
16.5 H
24 D

Tuned to 35hz and give me 70 squares of port...................

tick
tick
tick

just_in
11-14-2006, 09:30 PM
yea 2 15 32hz at 4.5 cubes a chamber
height 20
width40
depth20

iamamp3pimp
11-14-2006, 09:33 PM
nice thread.

Jared530
11-14-2006, 09:39 PM
Hey mobeious, plug those numbers in and give me a a pic w/demensions.

sdimeconcept
11-15-2006, 10:55 AM
I'm definitely interested. Would you mind doing a sketchup for me? I'm hoping to build it this weekend.

It's for a wedge style box that's going to be ported...

I'm not really sure if this is the best... but the sub is going to be inverted. I'm going to try and brace the box as well, but I'm not sure exactly how to measure to see what the final enclosure volume is....

WIDTH: 36 inches
DEPTH: 12 inches
HEIGHT 1(Back of box): 15 inches
HEIGHT 2(Front of box): 3 inches
THICKNESS: .75 inches

Enclosure Volume: 1.57227 cubic feet
Round port diameter: 3 inches
Round port length: 7.7 inches (Tuned to 35 Hz)

This is for a 10" Alpine TypeR 1022D

If you can do a sketchup of that for me, I'd greatly appreciate it. Thanks.

mobeious
11-15-2006, 07:15 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled_526699.jpg

there you go sdimeconcept

mobeious
11-15-2006, 07:17 PM
http://www.caraudio.com/gallery/1/4/2/9/8/15.JPG


there you go vetkilr

bri487
11-15-2006, 07:20 PM
someone can sketch one up for me if they want. i am not in a creative mood. its going to be fiberglass though, just cant think of a shape. two 12"s or one 15" ported with two amps that are 2 ft long each. amps need to be incorporated into it.

mobeious
11-15-2006, 07:30 PM
dont know how to do fiberglass shapes yet?

iamamp3pimp
11-15-2006, 07:36 PM
i dont.

Wonger
11-15-2006, 07:38 PM
How about I tell you what sub and amp I use. :)

bluelceii
11-15-2006, 09:05 PM
7.5 cubes @30-35 Hz CRX style if thats what they call it (port(s) firing back Subs firing up)

Edit: for a grand cherokee btw...

Lil_KB
11-15-2006, 09:09 PM
7.5 cubes @30-35 Hz CRX style if thats what they call it (port(s) firing back Subs firing up)

Edit: for a grand cherokee btw...

max dimensions? port area? subs being used?

im bored too...lol

bluelceii
11-15-2006, 09:27 PM
its for a friend, its going in his jeep. he's using 3 type Rs. so uh... i guess 36 W 16 H 30 D.

mobeious
11-15-2006, 09:57 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled2.jpg

there you go 3 type r ported

bluelceii
11-15-2006, 10:14 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled2.jpg

there you go 3 type r ported

whats that tuned to?

bri487
11-15-2006, 10:21 PM
dont know how to do fiberglass shapes yet?

im not to the point where i can frame and wrap, which is what i will end up doing anyway, but i cant really get my finger on something that pleases me yet. and when you sraw it it just doesnt look 100% right.

mobeious
11-15-2006, 10:41 PM
34

baseballer1100
11-15-2006, 11:03 PM
18 inch btl max width 41 max height 20 max depth 35 Tunes to 33

Lil_KB
11-15-2006, 11:46 PM
18 inch btl max width 41 max height 20 max depth 35 Tunes to 33

18" btl, 7 cubes at 33, 80 sq in of port, double baffled. 41 width 15.75 height 25 depth...(room for batteries, amp racks, cargo, or whatever you can fit.

http://i25.photobucket.com/albums/c81/Lil_KB/18btl733-2.jpg

baseballer1100
11-15-2006, 11:48 PM
18" btl, 7 cubes at 33, 80 sq in of port. 41 width 15.75 height 25 depth...(room for batteries, amp racks, cargo, or whatever you can make up.

http://i25.photobucket.com/albums/c81/Lil_KB/18btl733-2.jpg

**** thats bad ***. What are the dimensions of the panels?

Lil_KB
11-15-2006, 11:52 PM
give me a sec ill pm you a full description.

sunny201
11-15-2006, 11:55 PM
ummm if your still bored... Two 12" Audiobahn (plz dont bash) AW1206T and ported. No more than 30x20x15 inches Oh yea and Thanks

baseballer1100
11-15-2006, 11:57 PM
Sweet!!!

Jared530
11-16-2006, 12:12 AM
Ok yall, i need a little help. The box i have in right not is 14x21.5x38.5, and that is the max demensions that can fit into my car. what should i tune that as and how many with how many squares of porT? Im looking for loudness and spl.

Hey lil KB or mobeious when you get these number can you plug that into your 3D box designer. Also does the design also include demesions and all that?

xluben
11-16-2006, 12:25 AM
Ok yall, i need a little help. The box i have in right not is 14x21.5x38.5, and that is the max demensions that can fit into my car. what should i tune that as and how many with how many squares of porT? Im looking for loudness and spl.

http://www.subwoofertools.com/forum/ported-box.asp?Ew=38.5&Eh=14&Dia=6&Xmax=14&Vd=.08&NumW=2&Vb=4&Fb=32&Qts=&Vas=&Fs=&CE=0

4ft^3 @ 32Hz w/50 in^2 of port

that's about the most middle of the road box you can get :)

you didn't mention what subs you have, but that'll be decent with most :p:

EDIT: i guess you can get a little more with those dimensions (i read wrong before)

http://www.subwoofertools.com/forum/ported-box.asp?Ew=38.5&Eh=14&Dia=6&Xmax=14&Vd=.08&NumW=2&Vb=4.4&Fb=32&Qts=&Vas=&Fs=&CE=0

4.4ft^3 @ 32Hz w/50in^2 of port

baseballer1100
11-16-2006, 12:26 AM
Lil kb is the ****!!!

Lil_KB
11-16-2006, 12:35 AM
ummm if your still bored... Two 12" Audiobahn (plz dont bash) AW1206T and ported. No more than 30x20x15 inches Oh yea and Thanks

you dont have much room to work with...i squeezed out 3 cubes @ 32 hz...id consider just running one loud *** 12 if you cant get more room out of your trunk.

http://i25.photobucket.com/albums/c81/Lil_KB/212s332.jpg

Jared530
11-16-2006, 12:36 AM
lil KB, i have a 15" XXX (2005). What box would be better for me? the 1st or second one? And would this give me max SPL?

Lil_KB
11-16-2006, 12:36 AM
Lil kb is the ****!!!

np man...just tryin to help a fellow basshead out. let us know if you build that design and how it all goes. worklog w/ pics ftmfw.

Lil_KB
11-16-2006, 12:41 AM
lil KB, i have a 15" XXX (2005). What box would be better for me? the 1st or second one? And would this give me max SPL?

hmm...i dont have much experience with XXXs but it seems like it would need more port area than 50in^2. going by instinct the 4.4 box would be louder, but honestly i don't think you would really notice much of a difference between the 2 at the same tuning. anything 4-4.5 cubes should be nice.

baseballer1100
11-16-2006, 12:45 AM
I cant get winisd to work with the btl?

xluben
11-16-2006, 12:46 AM
lil KB, i have a 15" XXX (2005). What box would be better for me? the 1st or second one? And would this give me max SPL?

didn't realize it was a single 15"

if you want the port on the other face i can re-do the site thingy :)

as for box volume/port area for that driver i have no idea.

do you know the sub displacement and xmax?

Lil_KB
11-16-2006, 12:46 AM
what do you mean it wont work?

btw jared530, how are you fitting a 15" sub if your max height is 14"?

bluelceii
11-16-2006, 12:47 AM
LIL KB, I see that mobeious made me a 3D design, Can you make me one with a full spec sheet??

3 type Rs. so uh... i guess 36 W 16 H 30 D. 7.5 cubes tuned round 30-35 Hz. I would like the Subs firing up and port going back but you can make it the way you want...

xluben
11-16-2006, 12:50 AM
what do you mean it wont work?

not sure who this is referring to


btw jared530, how are you fitting a 15" sub if your max height is 14"?

i'm guessing the sub isn't on the 14" face (up-fire, probably)

Jared530
11-16-2006, 12:51 AM
ok, how about 60cubes of port? it handles like 1500wRMS and im giving it 2300watts RMS. And the current port has alot of port noise. What do you think. Anyone have any suggestions on how many cubes my port should be?

Lil_KB
11-16-2006, 12:51 AM
LIL KB, I see that mobeious made me a 3D design, Can you make me one with a full spec sheet??

3 type Rs. so uh... i guess 36 W 16 H 30 D. 7.5 cubes tuned round 30-35 Hz. I would like the Subs firing up and port going back but you can make it the way you want...

d*mn....i had started one for you too but when i saw mobeious posted one i stopped and forgot to save it. ill start working on another one though.

3 12s im guessing?

Lil_KB
11-16-2006, 12:52 AM
not sure who this is referring to



i'm guessing the sub isn't on the 14" face (up-fire, probably)



that was referring to baseballer1100, he said winsid wasnt working with the btl...


and yea i just thought about upfire.

bluelceii
11-16-2006, 12:52 AM
d*mn....i had started one for you too but when i saw mobeious posted one i stopped and forgot to save it. ill start working on another one though.

3 12s im guessing?

yuuuuuuuup

Lil_KB
11-16-2006, 12:53 AM
ok, how about 60cubes of port? it handles like 1500wRMS and im giving it 2300watts RMS. And the current port has alot of port noise. What do you think. Anyone have any suggestions on how many cubes my port should be?

how big is your current port?

id give it like 75+ just to be safe.

Jared530
11-16-2006, 12:57 AM
ok yea 75 sounds cool. I dont know how big my current port it. Too small ill tell u that. Would it be cool if u designed a box? with demensions and all that? thanks bro

Lil_KB
11-16-2006, 01:01 AM
sure...your sub is upfiring? whats the mounting depth on it?

bluelceii
11-16-2006, 01:06 AM
Lil KB: you forget about me or you workin on it??

BoondockSaints
11-16-2006, 01:11 AM
Dodge Ram 1500 Ext Cab (01)
2 12" Mags. :)
If you need teh dimensions I got a vague idea of what they are.

Lil_KB
11-16-2006, 01:11 AM
Lil KB: you forget about me or you workin on it??

im starting on it now.

bluelceii
11-16-2006, 01:21 AM
im starting on it now.

k kool .... sorry man didnt mean to rush ya. what program are you using?

Jared530
11-16-2006, 01:23 AM
sure...your sub is upfiring? whats the mounting depth on it?

Well the mounting depth for a XXX 12 is 11 1/8th, i couldnt find the specs for the 15", re doesnt really do a good job posting their specs.

BoondockSaints
11-16-2006, 01:28 AM
Im guessing we need to find dimensions for you?

Jared530
11-16-2006, 01:34 AM
yea

Lil_KB
11-16-2006, 01:42 AM
k kool .... sorry man didnt mean to rush ya. what program are you using?

google sketchup and winisd.

heres the product. i had to add 1.5" more height to get to 7.5 cubes if you don't mind.

tuned to 33-34. 104 in^2 of port.

http://i25.photobucket.com/albums/c81/Lil_KB/7.jpg

let me know if you like it and then ill send the full dimensions for each panel.

Lil_KB
11-16-2006, 01:44 AM
Dodge Ram 1500 Ext Cab (01)
2 12" Mags. :)
If you need teh dimensions I got a vague idea of what they are.

u squeezing those under the seat?

Lil_KB
11-16-2006, 01:48 AM
no responses, so im going to sleep.

pm me and ill answer in the morning if you want.

Lil_KB
11-16-2006, 01:48 AM
no responses, so im going to sleep.

pm me and ill answer in the morning if you want.

bluelceii
11-16-2006, 01:53 AM
google sketchup and winisd.

heres the product. i had to add 1.5" more height to get to 7.5 cubes if you don't mind.

tuned to 33-34. 104 in^2 of port.

http://i25.photobucket.com/albums/c81/Lil_KB/7.jpg

let me know if you like it and then ill send the full dimensions for each panel.

edit: n/m that looks good. send the spreadsheet to my email I pm'ed you...

Jared530
11-16-2006, 10:36 AM
Hye lil KB, did u happen to get that layout for my box with 75 cubes of port? By the way, what program are you using>

matt_martin87
11-16-2006, 12:49 PM
could you sketchup a 3-d model of this plan?

http://i9.photobucket.com/albums/a63/mathyouakandn/fiqboxplan.jpg

vetkilr
11-16-2006, 08:30 PM
http://www.caraudio.com/gallery/1/4/2/9/8/15.JPG


there you go vetkilr

No demensions??
How long is the port?
How big is the port?

seth350
11-16-2006, 08:36 PM
Very nice :)
I would let you make me a model, but from the looks of it you have enough on your plate lol

grillman6000
11-16-2006, 08:54 PM
can i get.....

4.5^ft @ 32hz for two 12's

max dims..
36"wide
15"high
20"deep

b.t.w....what program are you using ?

Jared530
11-16-2006, 10:16 PM
NO! me first. lol. so wat program are you using?

Lil_KB
11-16-2006, 10:22 PM
i said before....

winisd for the calculations,

google sketchup for the 3d models.

and ill try to get to everyone, jared530 is next in line.

baseballer1100
11-16-2006, 10:24 PM
Lil kb is the ****!!

baseballer1100
11-16-2006, 10:24 PM
And is it winisd pro?

Lil_KB
11-16-2006, 10:25 PM
yes.

Jared530
11-16-2006, 10:46 PM
yeaaaaa!

aaron7114
11-16-2006, 11:03 PM
Lil_KB i just pm you with my request. Hope you can do it! Thanks in advance! :D

str8up2fast4u
11-16-2006, 11:15 PM
are you using vectorworks ta do these images your creating mobeious

baseballer1100
11-16-2006, 11:19 PM
Thats sketchup.

SQBubble
11-16-2006, 11:57 PM
how do you do 3d models with google skechtup with transparency and wood thickness??

Jared530
11-17-2006, 02:31 AM
................

Jared530
11-17-2006, 02:32 AM
not to be impatient or anything. lol .

sdimeconcept
11-17-2006, 02:39 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled_526699.jpg

there you go sdimeconcept

Thanks a bunch!

Lil_KB
11-17-2006, 05:04 PM
sorry jared530...my internet was having trouble last night.

3.8 cubes @ 33 hz, 63 in^2 of port. (thats all i could fit really, should be good at a lower tuning like 33.)

http://i25.photobucket.com/albums/c81/Lil_KB/xxx1.jpg

n0liab0y
11-17-2006, 06:32 PM
could u sketch me 1 for 2 type-r 12s. max dimensions 38width x 16height x 24.5depth.
tuned somewhere between 32-35hz.

Lil_KB
11-17-2006, 06:57 PM
could u sketch me 1 for 2 type-r 12s. max dimensions 38width x 16height x 24.5depth.
tuned somewhere between 32-35hz.

http://i25.photobucket.com/albums/c81/Lil_KB/212rs5.jpg

5.5 cubes, 32 hz, 66 in^2 of port.

my 2 12" type rs got VERY loud in the same size and tuning on 2k watts.

Frankensuby
11-17-2006, 07:15 PM
If your still up for this...

I need a right angle triangular sealed enclosure, 16." high, 10" depth, 12" wide, with the sub on the straight up side (facing back of trunk). 10" subwooder with 6.5" mounting depth.

Kind of a smaller width version or SMI's trinagular enclosure, but reverse, with the sub on flat side vs sloped side.

If it has the information, I need to know the volume of the enclosure.

Thanks
~Levi

iamamp3pimp
11-17-2006, 07:21 PM
free designs?

nice.

n0liab0y
11-17-2006, 07:36 PM
http://i25.photobucket.com/albums/c81/Lil_KB/212rs5.jpg

5.5 cubes, 32 hz, 66 in^2 of port.

my 2 12" type rs got VERY loud in the same size and tuning on 2k watts.

can u pm me with a full description on dimensions and everything

Jared530
11-17-2006, 08:28 PM
sorry jared530...my internet was having trouble last night.

3.8 cubes @ 33 hz, 63 in^2 of port. (thats all i could fit really, should be good at a lower tuning like 33.)

http://i25.photobucket.com/albums/c81/Lil_KB/xxx1.jpg

Thanks for the sketchup, but i was wondering if this camp with measurments and cut lengths?

Jared530
11-17-2006, 08:28 PM
Yea just like noliaboy said, because i plan on building this box this weekend.

Lil_KB
11-17-2006, 08:34 PM
give me a lil while and ill have dimensions all sent out...im debadging my truck right now and gotta run somewhere right quick after. ill have them out tonight most likely, or tomorrow at the latest.

also, im not gonna be doing any more designs. i think ive done my fair share of freebies for now.

Jared530
11-17-2006, 08:36 PM
hahaha yea i bet you didnt expect to be bombarded with this much work. I just want to thank you for taking the time to do this for us.

bluelceii
11-17-2006, 09:16 PM
free designs?

nice.

I tell you one thing.... I never knew how many didnt wanna pay $15 for s design that doesnt take him a couple of minutes to make... not trying to start anything tho... but all I needed was the google sketch-up design and i could look on that myself and firgure up on my own what size MDF to buy/cut... I'd understand if the program costed something but..... its free. Plus he's helping people like me out so we don't have to go through sooo much trouble just to do something like that...

Frankensuby
11-17-2006, 09:57 PM
I tell you one thing.... I never knew how many didnt wanna pay $15 for s design that doesnt take him a couple of minutes to make... not trying to start anything tho... but all I needed was the google sketch-up design and i could look on that myself and firgure up on my own what size MDF to buy/cut... I'd understand if the program costed something but..... its free. Plus he's helping people like me out so we don't have to go through sooo much trouble just to do something like that...

I'd be able to design my own system, but I don't know what software to use, or probably how to use it.

~Levi

Frankensuby
11-17-2006, 11:06 PM
winisd only calculates the response curve, I needed an actual 3d image designer :(

bluelceii
11-17-2006, 11:08 PM
winisd only calculates the response curve, I needed an actual 3d image designer :(

google sketch-up... will do it...

Frankensuby
11-18-2006, 12:39 PM
I did an ugly sketch of the box, but I'm on a mac and photobucket won't allow me to upload it for some reason.

FunBoyThomper
11-18-2006, 04:48 PM
can you sketch me up a plan for a 15" alpine type R?

room i have is 30 wide 15 tall 17 depth (i can go maybe a 1/2 inch to an inch on height)

i already attempted building a box, but miscalculated and cant get the box through the opening, but it was a **** good build

im trying to get something at 2.7-3 cubes at 30hz, unless you can reccomend somthing else that would work better, then that would help out alot

FunBoyThomper
11-18-2006, 04:57 PM
hot diggity dam, im too late :( no more sketches at all?

Frankensuby
11-18-2006, 05:30 PM
http://www.caraudio.com/gallery/2/9/2/8/9/Slide1.JPG

This box Will hopefully have around .75 cubes sealed. We'll see.

It is a rough draft, the final will be curved on the left side to fit under my rear strut section structure.

~Levi

chartman18
11-18-2006, 07:18 PM
Anything for dual 12" Type-R subwoofers, space is around max 35-36 width, 14-15 heighth, and 17-18 inches max depth, ported.

Frankensuby
11-18-2006, 09:04 PM
Anyone able to figure out volume for me if I give you the Sketch file? I cannot do it for the life of me, and I can't find a software that can give me internal volume :crap:

~Levi

BoondockSaints
11-18-2006, 11:19 PM
Hey wanna model a box for under neath the seats for my 01 Quad Cab Ram? :)
2 12 Mags

mobeious
11-19-2006, 07:26 PM
anyone else?

baseballer1100
11-19-2006, 07:45 PM
2 18 inch fully loaded btls dual 1 ohm max dimensions forty one inches wide 28 inches deep and 18 inches high. With interchangable ports at 30hz and fortyhz.

Frankensuby
11-19-2006, 08:21 PM
Mobeius---

If I throw you my google sketch file, can you figure out the volume of the enclosure? I have yet to get a reliable answer.

baseballer1100
11-19-2006, 08:21 PM
2 18 inch fully loaded btls dual 1 ohm max dimensions forty one inches wide 28 inches deep and 18 inches high. With interchangable ports at 30hz and fortyhz.

That would be amazing. If you could do that.

mobeious
11-19-2006, 09:05 PM
sure man send it over mobeious@hotmail.com

mobeious
11-19-2006, 09:07 PM
baseballer1100 you only have 10 cubes before port and sub displacement i dont think that is going to be enough for 2 18's

seg_representin
11-19-2006, 09:11 PM
I need a sketch. Got 2 12" kicker L5's and would like a ported box and don't have that much room in the trunk. Just shoot me a pm.

mobeious
11-19-2006, 09:31 PM
keep it in the post so my PM's dont go crazy i need maximum dimension and tuning?

baseballer1100
11-19-2006, 09:32 PM
baseballer1100 you only have 10 cubes before port and sub displacement i dont think that is going to be enough for 2 18's

you can go deeper. to about 33 inches

mobeious
11-19-2006, 09:37 PM
still not enough man you need atleast 6.5-7cubes per driver.... have you thought about 15's

baseballer1100
11-19-2006, 09:46 PM
nope... you can go 22 inches high.

AlpineUser
11-19-2006, 10:26 PM
chartman18 do you have aim if so pm me you s/n i can help you out on a design for ur 2 12's i just built a box for 2 12" Type R's today gotta carpet tommrow then im done but yeah i definatly can help u out

mobeious
11-19-2006, 10:32 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled_844866.jpg

there you go baseballer1000

baseballer1100
11-19-2006, 10:33 PM
Thats ******. i love you.

baseballer1100
11-19-2006, 10:35 PM
How deep is the port any other angles? Sorry for being so picky.

mobeious
11-19-2006, 10:37 PM
SPL port is 7.5" deep and the SQL port is 11.5"

mobeious
11-19-2006, 10:38 PM
http://www.caraudio.com/gallery/1/4/2/9/8/greg.jpg


this is one that im working on for a friend single RE SE 12 with zapco amps on top

baseballer1100
11-19-2006, 10:38 PM
Your The Man!!!

mobeious
11-19-2006, 10:40 PM
tips are apreciated at Mobeious@hotmail.com "paypal"

vetkilr
11-19-2006, 10:40 PM
No demensions??
How long is the port?
How big is the port?

:D

vetkilr
11-19-2006, 10:41 PM
15" sub

32 W
16.5 H
24 D

Tuned to 35hz and give me 70 squares of port...................

tick
tick
tick

:D

baseballer1100
11-19-2006, 10:41 PM
Cutsheet and ill give you a little somethin something :p:

mobeious
11-19-2006, 10:41 PM
this post is getting alot of replys

vetkilr
11-19-2006, 10:41 PM
http://www.caraudio.com/gallery/1/4/2/9/8/15.JPG


there you go vetkilr

:D

mobeious
11-19-2006, 10:49 PM
33.75 x 41 - 3 top/bottom
20.5 x 31.5 - 2 sides
20.5 x 41 - 3 front/back
12.5 x 20.5 - 1 SQLplugplate
20.5 x 7.5 - 2 SPLports
7.5 x 11.5 - 2 SQL port
18 x 11.5 - 2 SQL port

baseballer1100
11-19-2006, 10:50 PM
I love you.

seg_representin
11-19-2006, 11:32 PM
Yea maximum dimensions for the box for the 2 12" L5's ported are 17" tall, 30" wide, and 25" deep.

Jared530
11-20-2006, 12:39 AM
sorry jared530...my internet was having trouble last night.

3.8 cubes @ 33 hz, 63 in^2 of port. (thats all i could fit really, should be good at a lower tuning like 33.)

http://i25.photobucket.com/albums/c81/Lil_KB/xxx1.jpg

THank you

Jared530
11-20-2006, 12:40 AM
Hey mobious, can u finish were lil kb left off please and get some numbers.

n0liab0y
11-20-2006, 04:05 AM
Hey mobious, can u finish were lil kb left off please and get some numbers.

whut he said...i need to build a box

sl600
11-20-2006, 09:14 AM
i would be greatfull if you can make me box plan for 3 pioneer ts-w5000spl,
they are already in seald box each in 1.56 cu ft @ w14 x h16 x d 12(inner mesurments) with 1" mdf, but at higher volume one of them makes a cracking sound (like fire cracker) some say its bcs of the box ? and the manufacture recommends 1.5 cu for seald and 2 cu for ported,, your help would be appreciated.
thanks

overall box size is w46 x h18 x d14

Jared530
11-20-2006, 10:23 AM
noilaboy, is that ur ride? shits clean

nVRuckus
11-20-2006, 10:54 AM
wanna do a hard one? trunked out. 38" wide by 31 deep 14.5" high double baffle top, single baffle sides and bottom. bottom has a 2cuft cutout and fiberglass for the wheel well towards the back of the trunk, top mount 18" over the wheel well, 10 4" PVC in the front baffle going to the seats ;)

danteBirosel
11-20-2006, 12:11 PM
wanna do a hard one? trunked out. 38" wide by 31 deep 14.5" high double baffle top, single baffle sides and bottom. bottom has a 2cuft cutout and fiberglass for the wheel well towards the back of the trunk, top mount 18" over the wheel well, 10 4" PVC in the front baffle going to the seats ;)

Now that's a challenge. :yumyum:

nVRuckus
11-20-2006, 01:37 PM
thats the MT box ;) finished fiberglassing the bottom piece in last night when I put the glass to Kenny's wall.

n0liab0y
11-20-2006, 03:18 PM
noilaboy, is that ur ride? shits clean

yea its mine, preciate dat

mobeious
11-20-2006, 05:20 PM
seg representin thats not enough for 2 L515's its only 6cubes

mobeious
11-20-2006, 05:41 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled1.jpg

there ya go Jared530

vetkilr
11-20-2006, 05:43 PM
Can I get a box for a 15L7 with these deminsion and have them on the pic.

16H
32W
24 D
With 70 squares tuned to 35hz.
Sub on face towards trunk and the port side firing on the passenger side?
With all measurements:up2somet:
Port 4.75" W by 14.5" H and it would be around 31" Long give or take

Should be around 4.1 cubes afta everything.

mobeious
11-20-2006, 05:59 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled3.jpg

there you go NVRukus

djman37
11-20-2006, 05:59 PM
all right sir, lemme see what you can come up with. I need a box for SPL.
4 DD 9515's. vehicle peaks around 55hz, tune like 51hz. like 16-18 sqin of port per cube. I'd like either 4 subs and a slot at the end, or 4 subs surrounding a centered slot. Double thick top plate, I can handle a removable port. I'd like all subs/port facing up, but COULD accept a rear-firing port. 42" wide MAX, no deeper or taller than it has to be. good luck.

vetkilr
11-20-2006, 06:07 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled3.jpg

there you go NVRukus

Thats tight right there:up2somet:

mobeious
11-20-2006, 06:13 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled5.jpg

Vetkilr

vetkilr
11-20-2006, 06:16 PM
You the Man

kowboy
11-20-2006, 06:37 PM
You Got Pm.

Hey....I appreciate your generosity with your talent. I was wondering if you could help me out. I have two treo ssx 15's and I need a box tuned to 32hz subs up and port back. dimensions are 48"W x 21"H x ??"D. Any help would be really cool. Thx.

BTW...the subs displacement is .256ft. each. again, thx.

Jared530
11-20-2006, 09:20 PM
****, ur skilled with that program.

Jared530
11-20-2006, 09:26 PM
whats this measurment say?

mobeious
11-20-2006, 09:27 PM
5"

mobeious
11-20-2006, 09:28 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled4444.jpg

Kowboy

kowboy
11-20-2006, 09:48 PM
thanks a lot!! u are da man!

mobeious
11-20-2006, 09:49 PM
I do build boxes and any box on here i will build and ship to customer

phantom240
11-20-2006, 09:55 PM
Ive got a doozie for ya.

I got a space 36x24x12 tall to work with. I want to put 4 12's in this box, and upfiring seems to be the only way to do this. I would LIKE a slot port in the center of the box tuned to approx 30hz, firing foreward (cuz firing rear would fire an inch from the back of the car and be useless), made of 3/4" MDF with a double top baffle.

mobeious
11-20-2006, 09:59 PM
fireing in the car or on the same plane as the subs?

mobeious
11-20-2006, 10:01 PM
bro you only have 4cubes with those measurements good for about 2 12's

phantom240
11-20-2006, 10:07 PM
Polyfill works wonders.

...im also trying to set a record for my car. 4 12's in one of the smallest cars ive seen... While KEEPING the back seat! and Memphis M-class subs work best in smaller enclosures

mobeious
11-20-2006, 10:13 PM
your lookin at around 1cube each thats pusing it for sealed let alone ported its not going to sound good man then we havent even taking out displacement for port so really ur less then 1cube per sub

kowboy
11-20-2006, 10:22 PM
I do build boxes and any box on here i will build and ship to customer

PM me a price on mine shipped to 48310. Thx.

kowboy
11-20-2006, 10:27 PM
And btw, what's the net volume on my box?

phantom240
11-21-2006, 12:13 AM
Oh well. Ill just make it sealed then! lol. When i build it ported my back seat will be gone.

n0liab0y
11-21-2006, 02:17 PM
Could someone sketch me 1 for 2 type-r 12s with a full description on dimensions. My max dimensions are 38width x 16height x 24.5depth. I want it tuned somewhere between 32-35hz.

mobeious
11-21-2006, 05:36 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled_606649.jpg

noliaboy

djman37
11-21-2006, 05:38 PM
mobeious, i feel so neglected!:crying:

mobeious
11-21-2006, 06:04 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled2_869270.jpg

DJ man

djman37
11-21-2006, 06:10 PM
DJ man

yea!!!:D Nice straightforward design.

mobeious
11-21-2006, 07:22 PM
anymore

bluelceii
11-21-2006, 07:34 PM
Max dimensions: 36 W 16 H 30 D. I want ported... (wouldn't mind the port in the center but.... which ever works/sounds louder

(2) Audioque HD315


Woofer Size 15"
Fs 29
Qts .33
Qes .36
Qms 3.96
Vas 135
Le mH 1.1
Sensitivity 1W/1m 92 dB
Magnet Diameter 8.7"
Magnet Weight 330 oz
Coil Diameter 3.0"
Coil Length 44mm
Useable Throw 2.5"
Continuous Power 1000 W
Music Peak Power 2000 W
Mounting Depth ?"
Circle Cutout 14"

mobeious
11-21-2006, 07:43 PM
CRX style?

bluelceii
11-21-2006, 07:46 PM
CRX style?

nah.... i mean you can if it sounds better but if you ASKING ME then no.

mobeious
11-21-2006, 07:47 PM
what vehicle

bluelceii
11-21-2006, 08:11 PM
Jeep grand cherokee

mobeious
11-21-2006, 08:14 PM
you need to do crx

bluelceii
11-21-2006, 08:16 PM
you need to do crx

thats cool... what ya got?

berserker
11-21-2006, 08:17 PM
will take you up on your offer and help you from boredom


2 kicker cvr12s
subs fire up and the slot fire back or forward
double baffle
changeable ports
4.4 cubes 32-33 hz daily and 52-53 hz burper
35W x 17-20H x 30D max


along with a cut list as well... thank you!

baseballer1100
11-21-2006, 08:23 PM
Mobeious is tight.

mobeious
11-21-2006, 08:28 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled22.jpg

there blueice

mobeious
11-21-2006, 08:29 PM
BTW the center of the circle cutouts are 20" from the port side of the box and 8.25 from the side

mobeious
11-21-2006, 08:30 PM
**** all these cutlist and models and only one paypal tip

baseballer1100
11-21-2006, 08:32 PM
Your welcome. :)

djman37
11-21-2006, 08:35 PM
**** all these cutlist and models and only one paypal tip

i asked what you wanted for it!

Chevyaudio
11-21-2006, 08:39 PM
well...this is why I dont advertise free plans...If Im in the mood I will do one if not Its a Pain in the *** to put together a properly designed box...and BTW Mobeious YGPM about a file.

mobeious
11-21-2006, 08:50 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled33333.jpg


berserker

mobeious
11-21-2006, 08:50 PM
ahh well its all good im glad to help some peeps out...never new it would get this big

mobeious
11-21-2006, 08:54 PM
DJman

42x20.75 - 2 front/back
34.5 x 20.75 - 2 sides
42 x 36 - 3 top/bottom
34.5 x 4 - port

bluelceii
11-21-2006, 08:58 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled22.jpg

there blueice

you got the save file for this??

mobeious
11-21-2006, 09:33 PM
no sorry already deleated i dont save them

bluelceii
11-21-2006, 09:55 PM
whats it tuned to?

mobeious
11-21-2006, 09:56 PM
34

bluelceii
11-21-2006, 10:02 PM
you have AIM or yahoo messenger?

mobeious
11-21-2006, 10:05 PM
nah

80INCHES
11-21-2006, 10:12 PM
you got the save file for this??

right click on the pic and click on save picture as
and save it to your comp;)

thank me later...
mobeious..u doing a fine job with the sketchup

80

mobeious
11-21-2006, 10:12 PM
how yall like the new sig?

seg_representin
11-21-2006, 10:15 PM
seg representin thats not enough for 2 L515's its only 6cubes

They are 12's and i have a grand am if you have any experience with their trunks just trying to get these things out of a sealed box and into a ported box. Can't i use some polyfill if the box is a lil small?

mobeious
11-21-2006, 10:20 PM
well if they are 12's you got plenty room

djman37
11-21-2006, 10:30 PM
DJman

42x20.75 - 2 front/back
34.5 x 20.75 - 2 sides
42 x 36 - 3 top/bottom
34.5 x 4 - port

pm me your paypal addy.
sux to lose that much gear,
plus you do good work.

seg_representin
11-21-2006, 10:47 PM
Yea they are 12's

mobeious
11-21-2006, 10:48 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitledwerwer.jpg

seg

seg_representin
11-21-2006, 10:52 PM
Thanks...whats it tuned to?

baseballer1100
11-21-2006, 10:56 PM
ahh well its all good im glad to help some peeps out...never new it would get this big

People love free ****.

mobeious
11-21-2006, 10:58 PM
34

bluelceii
11-21-2006, 11:24 PM
I forgot to ask how many cubes was that box you designed me?

google123
11-22-2006, 03:40 AM
here is a simple one for ya. can u build this box right here but make it downfiring instead and with a 18" x 12" section in the angled side of it for an amp? the dimensions are as follows.

http://www.supercrewsound.com/uploads/ecomitem300a.jpg

# Dual 10 inch subwoofer cutout
# Sealed Enclosure
# 24" x 12" x 9.40" TD, 15.12" BD (WxHxD)
# Air space = .75 cubic feet per chamber
# 3/4" MDF Construction

how much to build and ship to zip 75455 thanks.

berserker
11-22-2006, 02:28 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled33333.jpg
berserker


thank you! YGPM

bluelceii
11-22-2006, 03:02 PM
right click on the pic and click on save picture as
and save it to your comp;)

thank me later...
mobeious..u doing a fine job with the sketchup

80

I meant the google sketch file... :rolleyes:

mobeious
11-22-2006, 05:57 PM
google123 ill get urs later tonight ................anymore?

scplayboy00
11-22-2006, 09:29 PM
Can u make me a 3.5cft tuned to 34hz for a ssd 15'?

mobeious
11-22-2006, 11:06 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled333.jpg

google123

djheadless24
11-22-2006, 11:20 PM
i need a box for one 15 inch cerwin vega v max the new ones

mobeious
11-23-2006, 12:55 AM
anymore?

sl600
11-23-2006, 10:42 AM
anymore?

how about 3 12" pioneer 5000spl, going sealed, dim w46xh18xd ? and its firing sideways
thank you

mobeious
11-23-2006, 06:48 PM
firing sidways?

THXdts
11-23-2006, 06:57 PM
I can do some to. I don't know how to design them, but I can draw them or whatever.

sl600
11-23-2006, 07:09 PM
firing sidways?

skip the (sideways) thing, wrong chose of word, i ment the subs would be facing stright not firing upwards.
thanks

djman37
11-23-2006, 09:01 PM
firing sidways?

i'm building that box in the AM. any more specs? pm is fine.;)

PV Audio
11-23-2006, 09:07 PM
Mobeious, when you go into sketchup, click on Window > Model Info > Units and change it to fractional. That way, you see it at 27" instead of 2'3". Just a tip to make for easier reading :)

baseballer1100
11-23-2006, 09:18 PM
1 18 inch btl fully loaded dual 1 tuned to 33 max dimensions forty one inches wide 17.5 inches high 28 inches deep. Thanks.

mobeious
11-23-2006, 09:30 PM
http://i7.photobucket.com/albums/y290/mobeious/Untitled3333.jpg
18blt

baseballer1100
11-23-2006, 09:31 PM
so the port is 16 inches?

mobeious
11-23-2006, 09:32 PM
yep

baseballer1100
11-23-2006, 09:35 PM
sweet how do you do them so fast? and are you using winisd pro alpha?

mobeious
11-23-2006, 09:44 PM
i use winisd and leap..... i make them so fast because i took 4years of drafting

baseballer1100
11-23-2006, 09:45 PM
**** whats leap?

mobeious
11-23-2006, 09:46 PM
another program for designin boxes

mobeious
11-23-2006, 09:47 PM
i can almost do it in my head now from building so many boxes

baseballer1100
11-23-2006, 09:47 PM
haha i bet.

baseballer1100
11-23-2006, 09:48 PM
Wanna do one more?

PV Audio
11-23-2006, 09:49 PM
i can almost do it in my head now from building so many boxes
Really.

mobeious
11-23-2006, 09:49 PM
sure..... people that tip me get the hook up lol

baseballer1100
11-23-2006, 09:51 PM
Ok 18 inch btl fully loaded dual one max dimensions forty one inches wide 17.5 inches high 28 inches deep. With interchangable ports one at 32 hz and the other at like forty five.

PV Audio
11-23-2006, 09:52 PM
sure..... people that tip me get the hook up lol
If you can do the port length formula in your head, then you'd be the first that I've heard of.

baseballer1100
11-23-2006, 09:53 PM
I dont think thats what he is talking about and what is the formula?

THXdts
11-23-2006, 09:56 PM
I wanna try one :(. :P.

PV Audio
11-23-2006, 09:56 PM
I dont think thats what he is talking about and what is the formula?

Lv = (23562.5*Dv^2*Np/(Fb^2*Vb))-(k*Dv)

where,

Dv = port diameter (cm)
Fb = tuning frequency (Hz)
Vb = net volume (litres)
Lv = length of each port (cm)
Np = number of ports
k = end correction (normally 0.732)

mobeious
11-23-2006, 09:57 PM
really no that bad

Length = 2.35625x10 to the 4th power X port diameter x number of ports divided by box volume x tuning freq squared minus end corection vaule x port diameter

mobeious
11-23-2006, 09:58 PM
beat me haha

mobeious
11-23-2006, 10:03 PM
im callin it a night

baseballer1100
11-23-2006, 10:03 PM
Thanks man.

THXdts
11-23-2006, 10:08 PM
I could do some if I new how to design a box, or something that gave me dimensions..

PV Audio
11-23-2006, 10:37 PM
I could do some if I new how to design a box, or something that gave me dimensions..

:laugh: That's like saying that you could drive a car if you knew how to drive a car.

Jared530
11-23-2006, 11:52 PM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled1.jpg

there ya go Jared530

hey mobeious, if you give me a cut sheet for this box, ill give a break you some bread :greedy:

THXdts
11-24-2006, 09:18 AM
:laugh: That's like saying that you could drive a car if you knew how to drive a car.

I am just saying I can make it 3D.

mobeious
11-24-2006, 10:17 AM
jared

38.5x21.5 - 3 top/bottom
20x11.75 - 2 sides
11.75x38.5 - 2 front/back
11.75x14.75 - 1 port 1
11.75x5 - 1 port 2

vetkilr
11-24-2006, 10:23 AM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled5.jpg

Vetkilr

This Box is Made:up2somet:

Except we made the hole round for a different sub:laugh:

mobeious
11-24-2006, 10:26 AM
awsome post some picks and lemme know how it sounds

baseballer1100
11-24-2006, 10:41 AM
Hey what about mine :p:

mobeious
11-24-2006, 11:09 AM
http://i7.photobucket.com/albums/y290/mobeious/Untitled444444.jpg

baseballer

baseballer1100
11-24-2006, 11:18 AM
Cutsheet? :p:

iamamp3pimp
11-24-2006, 12:26 PM
:(

baseballer1100
11-24-2006, 12:27 PM
Lol...Im just checkiin out my options. I need it to be forty one inches wide.

vetkilr
11-24-2006, 12:39 PM
Lol...Im just checkiin out my options. I need it to be forty one inches wide.

hmmmmmmmmmmmmmmm:eyebrow:

baseballer1100
11-24-2006, 12:44 PM
What?

vetkilr
11-24-2006, 12:45 PM
What?

looks like this thread is stirrin up feelings:uhoh:

bluelceii
11-24-2006, 12:56 PM
obviously...

PV Audio
11-24-2006, 03:38 PM
Classic CA.com drama :)

Johnny Drama
11-24-2006, 03:53 PM
Uh....You designed djman37 a box. You were to tune it to 50 or 51hz IIRC...


I just looked at your specs on the box, and unless I am a complete moron you tuned the box to 40hz...???

So, The box is 42x36x23.25
taking off wood we are at 40.5x34.5x20.75
16.77 gross
sub disp=.95 for the 4 subs
port disp =.69 for 4.75x32.5x7.75

Total 15.16 net cu.ft.

Total tuning is 40.4hz


Not exactly what he asked for and not really correct in any way. Not to mention that for $15 I would expect to see better pics and an actual breakdown of the cuts.

How about a refund for a wrong plan?

Someone check my math...


EDIT: Pic was so poor that I missed the double baffle in the mesurements, still shouldnt be anywhere near 50hz

baseballer1100
11-24-2006, 05:31 PM
looks like this thread is stirrin up feelings:uhoh:

o haha

crazy4ozs
11-24-2006, 07:54 PM
im not guna lie...this thread is the ****...

wanna do one for me 2?

3cf @ 26Hz for 1 15" AVA...make the port on the side if u can ;)

PV Audio
11-24-2006, 08:16 PM
Uh....You designed djman37 a box. You were to tune it to 50 or 51hz IIRC...


I just looked at your specs on the box, and unless I am a complete moron you tuned the box to 40hz...???

So, The box is 42x36x23.25
taking off wood we are at 40.5x34.5x20.75
16.77 gross
sub disp=.95 for the 4 subs
port disp =.69 for 4.75x32.5x7.75

Total 15.16 net cu.ft.

Total tuning is 40.4hz


Not exactly what he asked for and not really correct in any way. Not to mention that for $15 I would expect to see better pics and an actual breakdown of the cuts.

How about a refund for a wrong plan?

Someone check my math...


EDIT: Pic was so poor that I missed the double baffle in the mesurements, still shouldnt be anywhere near 50hz
Hopefully we're missing something, because I'm also getting 41hz, but at 15.6 cubes. Even at 15.16 it's only 41.7.

saywhat?
11-24-2006, 08:27 PM
can someone give me specs of WHAT was asked for originally by DJman?

PV Audio
11-24-2006, 08:30 PM
Grant, you really gotta get a better av. I don't know about you, but I prefer current women to those who have now been dead for 20 years.

saywhat?
11-24-2006, 08:43 PM
vida guerra hasnt been dead for 20 yrs :fyi: oh and.......vintage style ftmfw.

djman37
11-24-2006, 09:17 PM
can someone give me specs of WHAT was asked for originally by DJman?

http://www.caraudio.com/forum/showpost.php?p=2462794&postcount=139

mobeious
11-24-2006, 09:45 PM
JnTar im getting 15.3cubes at 51hz vent 4.53 long exactly what i designed

mobeious
11-24-2006, 09:46 PM
vent is 34.5 not 32.5

mobeious
11-24-2006, 09:50 PM
jntar i dont think u should come on a thread and bash people that are doing others favors..... i did not tell him he owed me $15 he gave it in form of tip for doin it for him..... as far as pic quality if you want me to load it up and sharpen it for ya and blow it up to about 100mb so ur coke bottle glasses can see it i can do that for ya.... other then that get off the thread if he wants a refund ill give him his money back if he wants another sketch ill do that to,, doesnt matter to me im doin this as a favor for other people

mtdewelf
11-24-2006, 09:52 PM
jntar i dont think u should come on a thread and bash people that are doing others favors..... i did not tell him he owed me $15 he gave it in form of tip for doin it for him..... as far as pic quality if you want me to load it up and sharpen it for ya and blow it up to about 100mb so ur coke bottle glasses can see it i can do that for ya.... other then that get off the thread if he wants a refund ill give him his money back if he wants another sketch ill do that to,, doesnt matter to me im doin this as a favor for other people

forget them, this is one of the most helpful threads in awhile, oh yeah YGPM ;)

PV Audio
11-24-2006, 10:58 PM
jntar i dont think u should come on a thread and bash people that are doing others favors..... i did not tell him he owed me $15 he gave it in form of tip for doin it for him..... as far as pic quality if you want me to load it up and sharpen it for ya and blow it up to about 100mb so ur coke bottle glasses can see it i can do that for ya.... other then that get off the thread if he wants a refund ill give him his money back if he wants another sketch ill do that to,, doesnt matter to me im doin this as a favor for other people
It would probably be to your benefit to relax.

mobeious
11-24-2006, 11:03 PM
lol

mobeious
11-24-2006, 11:04 PM
18pgs and not one complaint tell he comes on here about someone elses box .... just bothers me... sorry bout the outburst

PV Audio
11-24-2006, 11:04 PM
lol
Trust me on this one :)

Jared530
11-24-2006, 11:05 PM
i was wondering what i should fill my box with? should i put a layer of foam in the box?

mobeious
11-24-2006, 11:05 PM
no prob

mobeious
11-24-2006, 11:06 PM
resin is ur friend

PV Audio
11-24-2006, 11:08 PM
i was wondering what i should fill my box with? should i put a layer of foam in the box?
Fill it as far as what? Resin doesn't do too much of anything except to seal your box tight. People say that it reduces turbulence, but in reality, you can potentially even lose output from resining. If you mean as far as damping materials go, it really depends on the enclosure, but closed cell foam (egg crate), Dacron, fiberglass (insulation i mean), and pillow stuffing all work well to increase the low end "clarity" a bit.

kowboy
11-24-2006, 11:22 PM
Hey mobeious...Do me up the same box as before (the dual one), but make it 3.5 cubes per sub, with 112 sq. in. of port area, okay? 48"wide, and 22"high and the depth can be whatever. Oh yeah, gimme your paypal addy so I can pay you for your help.

Johnny Drama
11-24-2006, 11:24 PM
JnTar im getting 15.3cubes at 51hz vent 4.53 long exactly what i designed


vent is 34.5 not 32.5

You are correct. I was wrong and will admit that. If your plans were better looking with a breakdown I never would have messed up.

I did say check my math...


Forgive me I F'd up.

-Justin

mobeious
11-24-2006, 11:36 PM
no prob jntar sorry for the outburst

djman37
11-25-2006, 12:12 AM
box is built, looks good...UPS JUST F'ED ME AGAIN. Baskets didn't make it, although they've been in mesquite since 4:38a THURSDAY.
never did get the centers. I ended up going 9" in and " over from the 4 corners. I could've put jntar AND chevyaudio in that thing!

Johnny Drama
11-25-2006, 12:17 AM
Pics???

http://img216.imageshack.us/img216/5236/file1binff7.jpg
http://img216.imageshack.us/img216/4661/file2binqe3.jpg
http://img329.imageshack.us/img329/4779/filebinud9.jpg

sorry for the cell phone pics...

Chevyaudio
11-25-2006, 12:25 AM
:fyi: Thats jntar's gay boy lemon water in the port.

PV Audio
11-25-2006, 12:25 AM
box is built, looks good...UPS JUST F'ED ME AGAIN. Baskets didn't make it, although they've been in mesquite since 4:38a THURSDAY.
never did get the centers. I ended up going 9" in and " over from the 4 corners. I could've put jntar AND chevyaudio in that thing!
Dude I've come to realize that the only shipping service I can rely on is me carrying my **** to the person's house. FedEx breaks my ****, and UPS is late.

Chevyaudio
11-25-2006, 12:27 AM
That box is my new house :fyi: and I plan on using it as a car once djman puts his DDs in there and powers them up...Just face the subs and port backwards, and away I go.

PV Audio
11-25-2006, 12:30 AM
That box is my new house :fyi: and I plan on using it as a car once djman puts his DDs in there and powers them up...Just face the subs and port backwards, and away I go.
You ever build that HT box for the CVR?

Chevyaudio
11-25-2006, 12:32 AM
No...lol. The CVR is in a CRX style box tuned at 24 hz sitting in my livingroom right now...LOL you gave me that plan about a year ago. I guess ill build it this christmans break...I mean afterall that CVR isnt a visualy apealing sub, and its kinda an eyesore in my living room, and that downfire box will fix that problem

baseballer1100
11-25-2006, 01:16 AM
http://www.caraudio.com/gallery/1/4/2/9/8/Untitled_844866.jpg

there you go baseballer1000

Hey if i turned the port sideways on this would it change anything?

mobeious
11-25-2006, 08:59 AM
no not really

baseballer1100
11-25-2006, 10:33 AM
Sweet. THanks man.

PV Audio
11-25-2006, 11:49 AM
Hey if i turned the port sideways on this would it change anything?
TRAITOR! :mad:








:D

baseballer1100
11-25-2006, 11:50 AM
What can i say?

mobeious
11-25-2006, 11:27 PM
i dont get it??

PV Audio
11-25-2006, 11:54 PM
i dont get it??
You need not be concerned :)

mobeious
11-26-2006, 12:07 AM
**** its like that huh

Gianotti
12-01-2006, 12:55 AM
trying to design something for me bro? 50Lx18Wx32H the space i can use/// 2 L7 15's 6cuft per sub ported tuned at 37hz

mobeious
12-01-2006, 09:53 PM
man u got ur measurments screwed i need width heigth depth ... what vehicle is it going in

chozen1
12-01-2006, 09:54 PM
do u have a sketchup of the 16 cube box for your 4 se15's

Ran4it2
12-01-2006, 10:08 PM
can i get a a box for a 10" 2 cubes at ike 30hz well im not arue abuot 2 cubes its for my brother RF p1 so whatever u think is good

mobeious
12-01-2006, 10:28 PM
yes i have sketchup for my 4 15's

bluelceii
12-01-2006, 10:50 PM
How bout 2 audioque HD315s crx style (or better) in a 97 eclipse hatchback

mobeious
12-01-2006, 10:54 PM
what is up with people trying to cram big speaker in little spaces....... 2 HD315's in the hatch of a eclipse.... try 2 12's u can be more effiecent with boxes being u prolly only have around 5 cubes to work with back there

Gianotti
12-01-2006, 11:21 PM
man u got ur measurments screwed i need width heigth depth ... what vehicle is it going in


*its goin in the ext. cab of a tacoma* ((it fits, i checkd numeruos times)))sorry man, ill make it easy, lol try to atleast. i need 12 cuft of box, i want the the subs and port firing the same way( towards the windshield) my dimenisons are(max)
width 50 x height 32 x depth 16....i can go 2in more max on depth, but im tryin to create room for my amp rack...any 3D sketchup would be cool...thanks man

Gianotti
12-01-2006, 11:23 PM
sorry forgot to add.......tuned round mid 30's the best for spl....

lippstuh
12-02-2006, 03:02 AM
can i get 2 sketches..
2 x 12" infiniti perfects
and
2 x 10" infiniti perfects


will be going into a coupe: 01 prelude

scplayboy00
12-03-2006, 12:30 AM
Will u sketch a box for a 15 fi ssd? 4 cubes at 34hz sub up and port back. Its going in a s-10 blazer.It needs to be 37in long 20in high and 17in wide. Is that enof for 4 cubes?