PDA

View Full Version : Need plans......free, if possible!



geowick07
10-19-2006, 09:02 PM
I was trying to use a kicker L7 15 sub, but my dimensions wont allow it...i only have 15 inches total vertical clearance in my trunk. so, i have to go to 2 12" L5's. my dimension's are as follows: 36in. wide x 15in. high x 26in deep(front to back). anyone have or can make these plans for me, i would appreciate it. Thanks!

matrxx dude
10-19-2006, 09:03 PM
www.suberwoofertools.com

geowick07
10-19-2006, 09:03 PM
edit: looking for between 4-5 cubes. sorry, should have said that in the beginning!

jeepintn
10-19-2006, 09:04 PM
nclosure section in the stickys and moe lester has a lot pf premade free plans, find one u can use and go with it

geowick07
10-19-2006, 09:04 PM
that link didnt work......page could not load

geowick07
10-19-2006, 09:06 PM
the ones in there are close....but i need the front piece to be 13.5" in high....so i can have something to screw the sub to. 13.5" plus the 2 pieces of mdf will equal my maximum height of 15"

PepsiFiend69
10-19-2006, 09:13 PM
why don't you just use the 15" and upfire it?


3-4 cubes is too small for 2 l7's IMO, especially if you want any kind of low end.



EDIT: sorry ididn't realize it said 4-5. cubes

geowick07
10-19-2006, 09:15 PM
cant fire up either cuz i am limited in space....basically, i am trying to keep the trunk liner, or cap, in place if i can. it is attached to the lid and moves up and down with the lid. and the clearance is only 15 inches from its underside to the trunk floor.

geowick07
10-19-2006, 09:17 PM
and i said 4-5 cubes for 2 L5's, not l7's. they only require 1.75 - 3.25 cubic feet each. hence, 4-5 cubes total.

PepsiFiend69
10-19-2006, 09:18 PM
gotcha.


what about 1 12" in 3.5 cubes tuned to 35 htz


i think that'd be nice and loud.

PepsiFiend69
10-19-2006, 09:19 PM
and i said 4-5 cubes for 2 L5's, not l7's. they only require 1.75 - 3.25 cubic feet each. hence, 4-5 cubes total.



L7s require the same airspace accoring to kicker.com

geowick07
10-19-2006, 09:21 PM
is it possible to build the box where the top doesnt sit on top of the sides, but rather inside the enclosure itself.? thus, i would eliminate 1.5 inches of height. could do that and maybe make the enclosure larger front to back?

ngsm13
10-19-2006, 09:21 PM
I can do one right now.

nG

geowick07
10-19-2006, 09:23 PM
do one what? some plans?

geowick07
10-19-2006, 09:24 PM
i was planning on one L7 15". since that wont fit, i am going with 2 L5 12's.

xluben
10-19-2006, 11:02 PM
http://www.subwoofertools.com/forum/ported-box.asp?Ew=36&Eh=15&Dia=7&Xmax=12&Vd=.12&NumW=2&Vb=4.5&Fb=35&Qts=&Vas=&Fs=&CE=0

how's that?

xluben
10-19-2006, 11:04 PM
http://www.subwoofertools.com/forum/ported-box.asp?Ew=36&Eh=15&Dia=7&Xmax=12&Vd=.12&NumW=2&Vb=4.9&Fb=32&Qts=&Vas=&Fs=&CE=0

for lower bass

geowick07
10-19-2006, 11:05 PM
will that hold a 15" L7? the cutout is 14 1/16 square.

xluben
10-19-2006, 11:05 PM
http://www.subwoofertools.com/forum/ported-box.asp?Ew=36&Eh=15&Dia=7&Xmax=12&Vd=.12&NumW=2&Vb=5&Fb=28&Qts=&Vas=&Fs=&CE=0

super duper low bass

or anywere inbetween those designs would be fine

xluben
10-19-2006, 11:06 PM
wtf, i thought you wanted it for two 12's and it should be 15" tall

if you can't figure out whether or not it'll fit you should not be around power tools

geowick07
10-19-2006, 11:10 PM
okay.....yeah, i was lookin at 2 12's or one 15 if i can make it fit.

geowick07
11-04-2006, 10:57 PM
well, ended up going with this enclosure plan. thanks for the link, xluben. here is the link to the box i am going to use. http://www.subwoofertools.com/forum/ported-box.asp?Ew=34&Eh=15&Dia=6&Xmax=18.2&Vd=.14&NumW=2&Vb=4&Fb=36&Qts=&Vas=&Fs=&CE=0

I am going to be running this setup: 2 Alpine Type-R's, @ 1 ohm, Hifonics BXi2006D, and the previous-linked enclosure.