PDA

View Full Version : Tang Bang 6.5" for small room



SQBubble
07-25-2006, 08:09 AM
ok, i have an old 2-channel receiver that puts out 70rms each @6ohm , and can go to 4ohm no prob. i tried it!!

i want to hook up 2 subs too it as I want some low end in my room!
i thought getting the Tang Bang 6.5"

http://www.partsexpress.com/pe/pshowdetl.cfm?&DID=7&Partnumber=264-832&scqty=2
btw they look so freakin great:D


ive already made a box plan for it, itll be 2.1cu.ft @ 33hz for each 6.5
and theyll be like floor standing enclosure..!!sub up and port down 40inch tall(its for my small room)

u guys think i would get reasonable low-end with 2tangbang 6.5 in these enclosure or it isnt worth it?(I know its only 6.5", but i dont have the power for a bigger sub nor i want to spend..6.5" in large enclosure is the best i can do!!i think)

thx:D

JimJ
07-25-2006, 11:08 AM
33Hz, IMO, is way too high for home use...I'd tune 10Hz lower :)

joetama
07-25-2006, 01:16 PM
I would agree for a sub in home theater you need it to be really really low......

SQBubble
07-25-2006, 01:32 PM
well its more for music, and sometimes i check out some movie but like around twice a month :rolleyes:
maybe @ 30hz wood make a good mix of music and movie??

and wut do you think about the driver(tangbang6.5")

thx alot

j3bus2k3
07-25-2006, 01:35 PM
I did a small 2.1 setup using a TangBand 8" and the Dayton 100W amp. The biggest problem I had in the box design was the god awful impedance spikes. My box is .75ft^3 at a wayyy to high 34hz. I'm going to redo it at 1ft^3 at 30hz...

There's a project on PE's website where a guy used 4 6.5" drivers off a 500W plate. Maybe you should check it out.

SQBubble
07-25-2006, 01:48 PM
I did a small 2.1 setup using a TangBand 8" and the Dayton 100W amp. The biggest problem I had in the box design was the god awful impedance spikes. My box is .75ft^3 at a wayyy to high 34hz. I'm going to redo it at 1ft^3 at 30hz...

There's a project on PE's website where a guy used 4 6.5" drivers off a 500W plate. Maybe you should check it out.


do it 2cu.ft or 1.5!! 1seem to small no?
can u link me the page on PE's website, i really cant find it
let us know how it sounds in the new box:)

thx man

j3bus2k3
07-25-2006, 01:49 PM
Its called the Boogeyman, lol : http://www.partsexpress.com/projectshowcase/boogieman/index.html

I'm home all week without a car so I could crank one out in a few hours...you have intrigued me good sir.

SQBubble
07-25-2006, 01:50 PM
btw, can someone tell me wut the Group Delay is??in winisd, i just dont get it:crap:

SQBubble
07-25-2006, 01:57 PM
Its called the Boogeyman, lol : http://www.partsexpress.com/projectshowcase/boogieman/index.html

I'm home all week without a car so I could crank one out in a few hours...you have intrigued me good sir.

thats an awsome project thx alot:D :D

JimJ
07-25-2006, 04:20 PM
btw, can someone tell me wut the Group Delay is??in winisd, i just dont get it:crap:

http://www.adireaudio.com/Files/TechPapers/GroupDelay.pdf

adio
07-25-2006, 05:10 PM
i'd tuned it from 26 - 30Hz

SQBubble
07-25-2006, 10:31 PM
http://www.adireaudio.com/Files/TechPapers/GroupDelay.pdf

thx alot,

so basically a group delay of 38ms is a big deal or its too much>?