PDA

View Full Version : Taking off Aeroports



Raisedin305
04-11-2006, 12:15 PM
Is there a way to take them off? I want to redo my box but not have to buy these ports again.

SPL140.2
04-11-2006, 12:19 PM
Is there a way to take them off? I want to redo my box but not have to buy these ports again.


honestly I dont know what would remove pvc glue, maybe soak them in goo gone for a couple of hours and try to pull them apart???

egg

davidfre21
04-11-2006, 12:23 PM
thats why i use duct tape :D

Quicker660r
04-11-2006, 12:26 PM
thats why i use duct tape :D


Me too!!

Raisedin305
04-11-2006, 12:35 PM
thats why i use duct tape :DThought about that when I realized I was missing a ring for one of the ports. I can take off one ports but not the other 7:crap:

Raisedin305
04-11-2006, 12:35 PM
You guys think a heat gun will be able to loosen it up a bit? I used PVC cement (glue).

Bolognablake
04-11-2006, 12:36 PM
If you can't dissolve the glue, try cutting them out with a jig-saw. Then you can chissel, sand, or grind the MDF away.

Raisedin305
04-11-2006, 12:40 PM
If you can't dissolve the glue, try cutting them out with a jig-saw. Then you can chissel, sand, or grind the MDF away.The front part I can take out for sure. The part that I cannot take out is the flares inside the box.

SPL140.2
04-11-2006, 12:41 PM
try callin a plumber they should give you an answer on how to dissolve the glue im sure.

tRiGgEr
04-11-2006, 12:41 PM
Should have used silicone/duct tape...

Raisedin305
04-11-2006, 12:42 PM
Should have used silicone/duct tape...Yeah I know but I didn't so now im trying to figure out how to get it off:crap:

Johnny Drama
04-11-2006, 12:43 PM
I silicone them to the box and duct tape them together. I have no clue how you would go about getting them out other then to take the subs out and saw the PVC. Once you saw them apart you can work on the glue on the flares.

djman37
04-11-2006, 12:48 PM
The front part I can take out for sure. The part that I cannot take out is the flares inside the box.

if you can take off the FRONT part, bring the rest out the SUB HOLE.

later.

nVRuckus
04-11-2006, 01:45 PM
cut the mdf apart and replace the one piece ;)

IamDeMan
04-11-2006, 02:09 PM
The front part I can take out for sure. The part that I cannot take out is the flares inside the box.UM my PP weren't as wide in the back flare as in the front flare. I was able to cut a hole big enough for it to fit through and still have plenty of material to screw the front flare/trim into. So mine was able to come in and out, until I was was dead set on it and kitty haired and bondoed over the lipt when flushing it in my FG box.

Raisedin305
04-11-2006, 09:56 PM
UM my PP weren't as wide in the back flare as in the front flare. I was able to cut a hole big enough for it to fit through and still have plenty of material to screw the front flare/trim into. So mine was able to come in and out, until I was was dead set on it and kitty haired and bondoed over the lipt when flushing it in my FG box.Tried getting mine out today and they won't come off. I hope I don't have to throw these away.

Raisedin305
04-11-2006, 10:29 PM
Could I just cut the back part of the flare off and buy the back flare new?

Buy a few of these?http://www.partsexpress.com/pe/showdetl.cfm?&DID=7&Partnumber=260-403

Raisedin305
04-11-2006, 10:48 PM
????

TypeRBass
04-15-2006, 06:57 PM
thats why i use duct tape :D
FTW!!!!!