PDA

View Full Version : Requesting box plans, will pay



bholtmeier
02-17-2006, 12:52 PM
Need Box Plans For a 12" Mag D2......left Moe a PM but no response...i'm workin with 28W 13.5H and 15D......lookin to get as close to 2cf as possible, and tuned as low as possible......will pay.....thanks, get back to me

GCAdidas13
02-17-2006, 12:55 PM
OK i'll do one irght now


*DIBS*


we'll work out a price later

GCAdidas13
02-17-2006, 12:56 PM
BTW if you have AIM send me one at gcadidas13

pjm2211
02-17-2006, 12:57 PM
what part of NE are you in? I'm in Omaha. mokedaddy ..(is in Omaha too)..who is a member of this forum is good at box/vent dimensions. he designed my vented box, and it sounds amazing. pm me if you want to hear it and are in/near omaha.

GCAdidas13
02-17-2006, 01:12 PM
Using every inch of your given dimensions, and 30 square inches of port area, the lowest tuning I can get is 37hz without dropping the port area more,

GCAdidas13
02-17-2006, 01:29 PM
Just for comparison... 2 cubes with 24sqin port area brings tuning down to 32hz

any way the box could be just a tiny bit bigger?

edit: going to class now, be back round 5

Ctminime
02-17-2006, 05:30 PM
well its in a 95 camaro so unless u made the box less wide at the bottom (witch IMO wouldnt be THAT hard to do) i know for a fact that ure not gonna get any bigger then that.... we had to remove some plastic from bholtmeiers hatch on his car to get that box to fit in......:crying:

bholtmeier
02-17-2006, 05:42 PM
Those are my MAX dimensions, any bigger will not work. 24 sq inch of port would be fine.....what kinda net volume do you get with that?

GCAdidas13
02-17-2006, 06:02 PM
Those are my MAX dimensions, any bigger will not work. 24 sq inch of port would be fine.....what kinda net volume do you get with that?
That's still exactly 2 cubes - but that's also before driver displacement (about 0.15 cuft)

So basically you're looking at 1.85 cubes tuned to 33 with 24 sq in of port area

GCAdidas13
02-17-2006, 06:42 PM
http://img217.imageshack.us/img217/7274/box16ou.jpg
Box

http://img217.imageshack.us/img217/9349/box28qe.jpg
Removed Top

Dimensions are follows:
Top and Bottom: 28" Wide x 15" Deep
Left and Right: 12" Tall x 15" Deep
Front (Baffle): 12" Tall x 23.75" Wide
Back: 12" Tall x 26.5" Wide
Port 1: 12" Tall x 12.25" Wide
Port 2: 12" Tall x 12.25" Wide

Volume: 2.00 Cubic Feet (before sub displacement)
Port Area: 24 Square Inches
Port Length: 28.25" (14.00" before bend, 13.25" after bend, 1.00" end correction)

Tuning Frequency: 31.6 Hz (disregards sub displacement, will be a touch higher)

GCAdidas13
02-18-2006, 01:14 PM
After a bit of thinking here are a few things you should know

When building your box, cut the hole for the sub last
Also make sure to use shorter screws near the sub hole so that you aren't screwing into where you will jigsaw later

PV Audio
02-18-2006, 02:55 PM
What program is that? I'm only wondering because that view makes it look trapezoidal.

GCAdidas13
02-18-2006, 03:19 PM
Autodesk Inventor 10

PV Audio
02-18-2006, 05:51 PM
Hmm, never heard of it. Looks good though.

bholtmeier
02-19-2006, 06:18 PM
Have made a fiew boxes before, just had cancelation issues with the first one and not enough port area on the second. Have yet to hear my mag in a decent box.

saywhat?
02-19-2006, 07:15 PM
i can help u out on my time available if u need, i feel bad cuz u keep spending all kinds of cash on this setup. free plan if u let me do it on my time, ill make it pretty sick for you, detailed as well.

Raisedin305
02-19-2006, 08:20 PM
i can help u out on my time available if u need, i feel bad cuz u keep spending all kinds of cash on this setup. free plan if u let me do it on my time, ill make it pretty sick for you, detailed as well.I'll take plans from this guy if I were you. He is one of the top 3 known here for plans.

saywhat?
02-19-2006, 08:43 PM
means a lot mang, from the people who have built from my plans, they dont have anything but good things to say.

PatFitz9
02-19-2006, 08:56 PM
I would take that offer. and not that it would happen, but worst comes to worst, it's free.

edit - i will be needing a box plan soon also, so if you like it, let everyone know :)

GCAdidas13
02-19-2006, 09:09 PM
Have made a fiew boxes before, just had cancelation issues with the first one and not enough port area on the second. Have yet to hear my mag in a decent box.
What do you think of the plans?

bholtmeier
02-19-2006, 11:38 PM
I compared them to one of Moe's pre made ones....pretty **** close

GCAdidas13
02-20-2006, 01:52 AM
Are you going to use it ?

If so, are you going to pay me ?

sebert5050 @ hotmail dot com

PV Audio
02-20-2006, 12:53 PM
LOL, get dat money.

PV Audio
02-20-2006, 12:54 PM
means a lot mang, from the people who have built from my plans, they dont have anything but good things to say.
You ever get that one finished for meatball? :laugh:

GCAdidas13
02-20-2006, 01:11 PM
LOL, get dat money.
... yes.

GCAdidas13
02-20-2006, 01:15 PM
/just read saywhat's post, top of this page...

****.

MikeyB
02-20-2006, 01:21 PM
Inventor is an awesome program, I use it everyday at school.

GCAdidas13
02-20-2006, 01:32 PM
Inventor is an awesome program, I use it everyday at school.
Yeah man. It is quite sweet. That is all.

saywhat?
02-20-2006, 02:22 PM
GCA i didnt see your post, i wont give a free plan, till yours in payed for. fair? i think so.

GCAdidas13
02-20-2006, 04:33 PM
GCA i didnt see your post, i wont give a free plan, till yours in payed for. fair? i think so.
kk:)

bholtmeier
02-21-2006, 10:32 AM
I'm actually going off of this ... http://img62.imageshack.us/my.php?image=175cubes32hz26sqin2rg.png

but i'm modifying the outside dimensions to 28x15x13.5........then all the internal dimensions accordingly...i'm just hoping the 26 sq inches port area will be sufficient for the mag....the slight modifications to the box shouldn't be noticeable should they?

bholtmeier
02-22-2006, 12:24 AM
...

bholtmeier
02-23-2006, 10:13 AM
well here is an update.......me and my friend (matt_martin87) had left over mdf from previous boxes and we used moe's modified plan to create this box: everything is cut, just need to assemble. took this pic with my phone, so i apoligize for the quality..

http://i25.photobucket.com/albums/c77/slikrider20/untitled.jpg

matt_martin87
02-23-2006, 12:08 PM
You should start a new thread on the box and its progression.