User Tag List

Closed Thread
Results 1 to 6 of 6

Reload Thread: How to wire 2 Type R's DVC at 2 Ohm on JBL 600.1

  1. #1
    thewoahna's Avatar
    thewoahna is offline Member



    Join Date
    Jun 2002
    Location
    Cleveland Area
    Posts
    66
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    How to wire 2 Type R's DVC at 2 Ohm on JBL 600.1

    OK, I am looking to get 2 Alpine Type R Subs (4 Ohm + 4 Ohm DVC) and a JBL 600.1 Amp. How would I wire the subs to this amp for a 2 Ohm load? I do not know much about DVC. Would I be better off getting the 2Ohm + 2Ohm DVC version?







  2. #2
    Jeff's Avatar
    Jeff is offline Member



    Join Date
    Mar 2002
    Location
    Texas
    Posts
    127
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I don't think you can get 2 ohms from two of those subs. Only 1,4,or 16.



    1999 GMC reg. cab. Sierra
    Factory HU and tweeters
    JBL p80.4
    JBL bp600.1
    CDT Cambria 6.5"
    (2) JL 10W0-4's

  3. #3
    thewoahna's Avatar
    thewoahna is offline Member

    Threadstarter


    Join Date
    Jun 2002
    Location
    Cleveland Area
    Posts
    66
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I am told that I can run them at 1 Ohm with that amp. Does anyone else run that Amp at 1 Ohm? I drive for about 3 hours, would this hurt the JBL 600.1? I dont want to "push" it too hard.




  4. #4
    Spddracer's Avatar
    Spddracer is offline Sounds Goooooood



    Join Date
    Mar 2002
    Location
    Ohio
    Age
    46
    Posts
    1,345
    Post Thanks / Like
    Images
    15
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Get dual 2 ohm r,s The 1 ohm load will shut the jbl off , Ive been there , It will clip and go into protection , Yes its 1 ohm stable but not when the subs move and drop below the 1 ohm , I ended up running mine at 8 ohm and it stil bumped , I had the 1200.1 on 2 12 type r's




  5. #5
    geonn's Avatar
    geonn is offline oalright



    Join Date
    Jan 2002
    Location
    minden, MI
    Age
    28
    Posts
    0
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    that amp is 1 ohms stable and with 2 dual 4ohm spekers you can not get a 2 ohm load. you can go 1 or 4 if ya want the 2 ohm load go with the dual 2ohm speakers. but that amp is stable at 1 ohm. to do that just run everything in paralell all + and all _ togeather




  6. #6
    MikeofTulsa's Avatar
    MikeofTulsa is offline The one and Only!



    Join Date
    Feb 2002
    Location
    Tulsa, OK
    Posts
    20,885
    Post Thanks / Like
    Images
    8
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)


    if u have the 2ohm dvc subs wire as follows...to get the 2 ohms....if they are 4 ohm dvc subs do the same and it will give you 4 ohms...good luck




Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum