Closed Thread
Results 1 to 3 of 3

Reload Thread: Help with Eclipse DA7232

  1. #1
    reible82nd's Avatar
    reible82nd is offline Senior VIP Member



    Join Date
    Jan 2011
    Location
    Lillington, NC
    Posts
    378
    Post Thanks / Like
    Mentioned
    7 Post(s)

    Help with Eclipse DA7232

    Hey guys, I just bought an Eclipse EA7232 from a local shop. I'm going to be running a Cadence Daytona 12D2 with it.

    I know it's a dual mono, so initially I thought I was going to have to run each voice coil to a channel, but there's a crossover setting on the amplifier which allows you to select stereo / L + R / Mono (L). If I'm interpreting that correctly, switching it to "mono" mode would series the internal amplifiers as I assume the (L) next to mono means that the right output wouldn't be used. If each side can run at 2-ohms, that would mean that I could series my sub and run a 4-ohm load to the left side of the amplifier.

    Maybe I'm completely off here, but I'm just trying to figure out whether I'll need to modify the wiring on my sub to run a voice coil to each side, or if I can series the sub inside the box and run a single length of cable to the left side of the amp using "mono" mode. Any help would be appreciated, thanks!



    2009 Toyota Camry
    Head Unit: JVC KW-R900BT
    Front Stage: Silver Flute 6.5s in doors, Dynaudio MD 102s in dash, PPI 356cs crossovers
    Rear Fill: MB Quart Discus (German) 6x9s
    Sub: Cadence Daytona 12 D2 in 2.5 ft3 @ 36Hz
    Mids/Highs Amplifier: Cadence TXA6004
    Sub Amplifier: JBL GTO24001
    Wiring: Monster 400 series 1/0 gauge, Big 3 w/ 2/0 gauge flexaprene, Mechman 240-amp
    Sound Deadening: 50 sqft Rattle Trap (trunk, front doors, rear dash)




  2. #2
    reible82nd's Avatar
    reible82nd is offline Senior VIP Member

    Threadstarter


    Join Date
    Jan 2011
    Location
    Lillington, NC
    Posts
    378
    Post Thanks / Like
    Mentioned
    7 Post(s)

    Re: Help with Eclipse DA7232

    Ok, I'm an idiot...I've done some additional research and identified that "mono" mode allows you to only use a single RCA cable hooked to the left RCA input.



    2009 Toyota Camry
    Head Unit: JVC KW-R900BT
    Front Stage: Silver Flute 6.5s in doors, Dynaudio MD 102s in dash, PPI 356cs crossovers
    Rear Fill: MB Quart Discus (German) 6x9s
    Sub: Cadence Daytona 12 D2 in 2.5 ft3 @ 36Hz
    Mids/Highs Amplifier: Cadence TXA6004
    Sub Amplifier: JBL GTO24001
    Wiring: Monster 400 series 1/0 gauge, Big 3 w/ 2/0 gauge flexaprene, Mechman 240-amp
    Sound Deadening: 50 sqft Rattle Trap (trunk, front doors, rear dash)

  3. #3
    mrkNOw1's Avatar
    mrkNOw1 is offline Member



    Join Date
    Sep 2010
    Location
    Denver, CO
    Posts
    67
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Help with Eclipse DA7232

    I had that same amp on 1 sub each channel to a 2 ohm voice coil on an hx2 15 and it worked fine wouldnt say id recommend it as it is basically two amps in 1 chassis. definitely dont wire it in a series across the two channels. that switch pertains to the rca inputs.




Closed Thread

Similar Threads

  1. Help with eclipse titanium
    By lextacy in forum Subwoofers
    Replies: 0
    Last Post: 07-02-2006, 01:39 PM
  2. help with Eclipse head unit
    By fastaccord in forum Head Units
    Replies: 8
    Last Post: 05-20-2005, 12:52 PM
  3. help with eclipse 5444, is something wrong?
    By TheAnswer808 in forum Head Units
    Replies: 1
    Last Post: 12-18-2004, 12:37 PM
  4. help with eclipse cd3402
    By ashre22 in forum Wiring, Electrical and Installation Help
    Replies: 6
    Last Post: 11-05-2004, 09:28 PM
  5. Need help with Eclipse 5301
    By tubbie in forum Wiring, Electrical and Installation Help
    Replies: 2
    Last Post: 03-09-2004, 01:51 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum