Closed Thread
Results 1 to 8 of 8

Reload Thread: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

  1. #1
    hgomez809's Avatar
    hgomez809 is offline Junior Member



    Join Date
    Dec 2012
    Location
    San Jose, Ca
    Posts
    4
    Post Thanks / Like
    Mentioned
    0 Post(s)

    How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    Hi everyone,

    I am kind of new to this and i am trying to figure out a way to connect all this together, i would appreciate if someone could help me.

    --Speakers 4x = Crunch P1-653 6.5" 800W 3-Way Car Speakers

    size/ type : 6.5" 3-way
    impedance: 4-ohms
    freq. responde: 59hz-20khz
    sensitivity / spl: 89db
    mounting depth: 2.13"
    power handling: 800 w
    RMS power: 55 w

    -- Sub 1x = AUTOTEK ATX12D4

    power handling: 350 w RMS and 700 w MAXX
    impedance: 4+4 ohms


    -- Amp 1x = KICKER ZX350.4 4 CHANNEL 350W AMP SPEAKER AMPLIFIER STEREO CLASS A/B ZX SERIES

    RMS Wattage at 2 Ohm x 4 Channels: 90
    RMS Wattage at 4 Ohm Bridged x 2 Channels: 175
    RMS Wattage at 4 Ohm x 4 Channels: 60
    Peak Wattage at 2 Ohm x 4 Channels: 180
    Peak Wattage at 4 Ohm Bridged x 2 Channels: 350
    Peak Wattage at 4 Ohm x 4 Channels: 120
    Stable down to: 2 Ohms
    Active Crossover: Low-Pass (Lp) 50 - 200 Hz, High-Pass (Hp) 50 - 200 Hz, Full (Ap)
    Bass Remote Included: No
    Channels: 4 Channel
    Cooling Type: Heatsink
    Power Ground: 4 Gauge
    Design: Class a/B
    Bass Boost: 0 - 18 Db
    Signal-to-Noise Ratio: >95db, a-Weighted, Re: Rated Power
    Dimensions (in): Length 13-1/2" X Width 9-5/8" X Height 2-1/8"
    CEA-2006 Compliant: Yes

    -- Head Unit (Stereo) 1x = BOSS AUDIO BV7280

    Screen Size: 3.2
    Monitor: YES
    FM: 18
    AM: 12
    Total Preset Stations: 30
    Switchable Radio Regions: USA, EUROPE, ASIA
    Remote: YES
    Body Mounting: Single DIN
    USB: YES
    SD Card: YES
    A/V Input: Yes
    Audio RCA Output: 2
    Video RCA Output: 1
    Subwoofer RCA Output: 1
    CCD Camera Input: YES
    Illuminated Controls: YES
    Clock: YES
    Preset Equalizer: YES
    ID3 Tag: YES
    Last Position Memory: YES
    Separate Bass and Treble: YES
    Balance and Fader Control: YES
    Loudness: YES
    Total Power Output: 320 Watts
    Total Number of Channels: 4
    Dimensions (H x L x W): 3.85" x 9.52" x 8.18"







  2. #2
    jungstah's Avatar
    jungstah is offline Senior VIP Member



    Join Date
    May 2012
    Location
    san francisco
    Posts
    278
    Post Thanks / Like
    Mentioned
    2 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    where is the amp for the sub? or am i missing something



    Pioneer AVH-P2400BT
    Stock Pioneer 4" components
    Hifonics Brutus BRZ1700.1D
    Two SA-12's
    cruddy prefab ported box----new box otw

  3. #3
    hgomez809's Avatar
    hgomez809 is offline Junior Member

    Threadstarter


    Join Date
    Dec 2012
    Location
    San Jose, Ca
    Posts
    4
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    right now i don't have an amp for the sub. i would like to know if there is any way i could put all this together for now?




  4. #4
    Shinju's Avatar
    Shinju is offline CarAudio.com Veteran



    Join Date
    Aug 2008
    Location
    Seattle
    Posts
    4,821
    Post Thanks / Like
    Mentioned
    23 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    You are going to have to run your front 2 channels at 80hz -> High pass (for example), then bridge your rear channels to your subwoofer and run the x-over were you want from 50-80 depending how punchy you want your bass.

    run your front RCA from your HU to the front input on the amp, if your deck has a sub out run that to the rear channel input on your amplifier.

    Easy peezy.



    List of Ref's Just ask, Shinju on all Car Audio Forums!


    Flawless Ebay Feedback User: Shadox2k2

  5. #5
    hgomez809's Avatar
    hgomez809 is offline Junior Member

    Threadstarter


    Join Date
    Dec 2012
    Location
    San Jose, Ca
    Posts
    4
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    Thanks for your answer, it sounds really easy, but i honestly have no idea on how to do any of that, could you explain me?




  6. #6
    jungstah's Avatar
    jungstah is offline Senior VIP Member



    Join Date
    May 2012
    Location
    san francisco
    Posts
    278
    Post Thanks / Like
    Mentioned
    2 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    he's saying to use the front outputs of your 4ch amp to power speakers and then bridge the rear output to power the sub w/ a low pass turned on.

    to give signal to the amp, use front rca out to front amp-input and then use subwoofer rca out to rear amp input



    Pioneer AVH-P2400BT
    Stock Pioneer 4" components
    Hifonics Brutus BRZ1700.1D
    Two SA-12's
    cruddy prefab ported box----new box otw

  7. #7
    hgomez809's Avatar
    hgomez809 is offline Junior Member

    Threadstarter


    Join Date
    Dec 2012
    Location
    San Jose, Ca
    Posts
    4
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    oh okay thanks but like how do i do that?

    how do i connect all the speakers to the 2 front channels? and how do i bridge the two read ouput to power the sub? and how do i turn on the low pass??

    & oh okay thanks




  8. #8
    jungstah's Avatar
    jungstah is offline Senior VIP Member



    Join Date
    May 2012
    Location
    san francisco
    Posts
    278
    Post Thanks / Like
    Mentioned
    2 Post(s)

    Re: How to connect this 4 speakers and 1 sub to a 4 channel amp and a HU?

    Quote Originally Posted by hgomez809 View Post
    oh okay thanks but like how do i do that?

    how do i connect all the speakers to the 2 front channels? and how do i bridge the two read ouput to power the sub? and how do i turn on the low pass??

    & oh okay thanks
    use the search function. seems like you have a LOT of learning to do.

    How to Bridge an Amplifier - Knowledge Base

    How to Tune and Adjust Amplifier Gains and Bass Boost - Knowledge Base

    Tools list - Amplifier Installation Guide



    Pioneer AVH-P2400BT
    Stock Pioneer 4" components
    Hifonics Brutus BRZ1700.1D
    Two SA-12's
    cruddy prefab ported box----new box otw

Closed Thread

Similar Threads

  1. How do i connect my amp and subs to my factory deck?
    By lechuga.adam in forum Amplifiers
    Replies: 2
    Last Post: 09-29-2012, 02:53 AM
  2. connecting 2 front, 2 rear speaker and sub to HU with 2 RCA outputs
    By bumpinsnow in forum Wiring, Electrical and Installation Help
    Replies: 2
    Last Post: 02-27-2010, 06:46 PM
  3. How to wire this 4ohm dvc sub to a 08zx750.1 kicker mono amp?
    By ExplicitUrSelf in forum General Discussion
    Replies: 7
    Last Post: 03-22-2009, 06:37 PM
  4. Speaker and Sub to Amp wiring question (ohms)
    By rlm1014 in forum Wiring, Electrical and Installation Help
    Replies: 1
    Last Post: 01-18-2009, 11:10 PM
  5. how to wire dual 1 ohm sub to 2ohms and .5 ohm??????
    By memphis_vette in forum Wiring, Electrical and Installation Help
    Replies: 8
    Last Post: 08-13-2008, 09:00 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum