Need some real good advice...

[Kyo]

Hi, Im building a system and Im looking for a one or a couple of 10 or 12 in. subwoofers and a good amp that can push them..

I dont want to be heard 3 blocks away but im looking for something decent that will give a good base sound and a pretty good kick that you can feel for a reasonable amount of money im looking to improve the overall sound quality of my system not something for competition..

I have a nissan sentra and I'll have to put them in the trunk, can some one advise me a good (one or two) subwoofer(s) and amp that I can go for?

Thx.

[jbl_marshall21]

well u could get a couple 10 inch K's. www.edesignaudio.com

type R 10's or type S's could do you since u don't want to be heard along ways away (don't know y you would want to be heard that far away)

both would sound very sweet.

[Spddracer]

Hi, Im building a system and Im looking for a one or a couple of 10 or 12 in. subwoofers and a good amp that can push them..

I dont want to be heard 3 blocks away but im looking for something decent that will give a good base sound and a pretty good kick that you can feel for a reasonable amount of money im looking to improve the overall sound quality of my system not something for competition..

I have a nissan sentra and I'll have to put them in the trunk, can some one advise me a good (one or two) subwoofer(s) and amp that I can go for?

Thx.

After having just about every sub made I bought a set of Image dynamics idqv2 10's . These are very very good sounding subs and take up very littel space .5 cuft per sub . Let me tell you this hit hard and clean . For around 100 each I dont think theres a sub that can touch them !

[Kyo]

Ok I was thinking probably getting either Audiobahn A2801T (Class A/B) or Audiobahn A8002T (The Intake one) I can get either one for about $200.00 I was thinking to bridge them down to a 12 in sub... Which one of these you all think will do the best job?

A2801T:

Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Double Sided Glass Epoxy Circuit Board
THD: 0.02%
S/N Ratio: >100dB
Frequency Response: 10Hz - 40KHz (+/- 1dB)
Variable 18dB Hi-pass Crossover: 50Hz - 750Hz
Variable 18dB Low-pass Crossover: 30Hz To 120Hz
Bass boost @ 45Hz: 0/18dB
Subsonic Filter: 20Hz to 50Hz
RCA Throughput Connections
3-way Protection Circuitry: Thermal, Short Circuit and Overload; Cooling Fan
Cobalt Blue Illumination
High gloss Chrome Plated Finish
Nickel Plated Block Terminals

4 ohms stereo 200x2 rms
2 ohms stereo 280x2 rms
4 ohms mono 560x1 rms


-------------------------------------

A8002T:

Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Semi-double Glass Epoxy Circuit Board
THD: 0.02%
S/N Ratio: >100dB
Frequency Response: 10Hz - 40KHz (+/- 1dB)
Variable 18dB Hi-pass Crossover: 50Hz - 750Hz
Variable 18dB Low-pass Crossover: 50Hz To 120Hz
Bass boost on/off
Subsonic Filter: 20Hz to 50Hz
RCA Throughput Connections
3-way Protection Circuitry: Thermal, Short Circuit and Overload; Cooling Fan
Cobalt Blue Illumination
High gloss Chrome Plated Finish
Nickel Plated Block Terminals
Air Induction Fan Cooled
RCA and Speaker Level Inputs

4 ohms stereo 200x2 rms
2 ohms stereo 400x2 rms
4 ohms mono 800x1 rms

----------------------------------------------------

Please check out http://www.audiobahninc.com/frameset.html

thx.

[jemorgan85]

Ok I was thinking probably getting either Audiobahn A2801T (Class A/B) or Audiobahn A8002T (The Intake one) I can get either one for about $200.00 I was thinking to bridge them down to a 12 in sub... Which one of these you all think will do the best job?

A2801T:

Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Double Sided Glass Epoxy Circuit Board
THD: 0.02%
S/N Ratio: >100dB
Frequency Response: 10Hz - 40KHz (+/- 1dB)
Variable 18dB Hi-pass Crossover: 50Hz - 750Hz
Variable 18dB Low-pass Crossover: 30Hz To 120Hz
Bass boost @ 45Hz: 0/18dB
Subsonic Filter: 20Hz to 50Hz
RCA Throughput Connections
3-way Protection Circuitry: Thermal, Short Circuit and Overload; Cooling Fan
Cobalt Blue Illumination
High gloss Chrome Plated Finish
Nickel Plated Block Terminals

4 ohms stereo 200x2 rms
2 ohms stereo 280x2 rms
4 ohms mono 560x1 rms


-------------------------------------

A8002T:

Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Semi-double Glass Epoxy Circuit Board
THD: 0.02%
S/N Ratio: >100dB
Frequency Response: 10Hz - 40KHz (+/- 1dB)
Variable 18dB Hi-pass Crossover: 50Hz - 750Hz
Variable 18dB Low-pass Crossover: 50Hz To 120Hz
Bass boost on/off
Subsonic Filter: 20Hz to 50Hz
RCA Throughput Connections
3-way Protection Circuitry: Thermal, Short Circuit and Overload; Cooling Fan
Cobalt Blue Illumination
High gloss Chrome Plated Finish
Nickel Plated Block Terminals
Air Induction Fan Cooled
RCA and Speaker Level Inputs

4 ohms stereo 200x2 rms
2 ohms stereo 400x2 rms
4 ohms mono 800x1 rms

----------------------------------------------------

Please check out http://www.audiobahninc.com/frameset.html

thx.

I guess 200 isnt a bad deal for it... but i would rather have something that did not say audiobahn on it.

check out these subs

http://www.partsexpress.com/pe/pshow...=297-656&DID=7

[Kyo]

So which one should I go for?
A2801T or A8002T

[Kyo]

I was also thinking to get one (due space issues in the trunk) dual voice coil (2ohms+2ohms) and have each channel connect to each one..

[shanerz21]

check out ebay, look at MA AUDIO .. sound very good

[iceteebone]

threads 2 years old dude. you aren't off ta good start at ca.com are you?