Plus side view
Plus side view
Deck: Pioneer 80PRS
Front Stage: Incriminator Audio I65C / Front Amp: Alpine MRV F540
Sub: 2 10" Obsidian V3 / Sub Amp: MMATS 2000.1
Bought From: ge_off_me, Boomsday, Chemmins, impactas, Sleazebagger, NoPh33rRaCiNg, fasfocus00, 50cents, flastrongman, pborcich, ace_800, GAMEOVERCCA
Sold To: Jamesmington, Juicee, Bunkrd you, Donnie Darko, ge_off_me, destined2race, todd131, Imjtnotu, mclerico83, aimology, Audiobahn, kpetree
Traded With: ge_off_me, Imtjnotu, 04lariat
And they sound very pleasant! :-D
System Layout help available via PM.
Sent you a PM, thought I would take a shot here too. Even trade for this?
Last edited by go_go_thrash; 05-30-2011 at 02:42 AM. Reason: fatfingered the keyboard
When my favorite sports team loses, it makes me want to hit my girlfriend.
definitely interested but I have to try at least the dc ref I just got first. Then Ill get back to you on that trade. Still cash rules
trade beast for beast ???
older treo ssx 125.2
Cant trade for subs unless you have an audiomobile evo or new alpine type r shallow t line.
I have a stealthbox and need a sub 10" that takes power and is less than 5.25" deep. My IDQ v2 10 cant keep up at high volume.
Oh I forgot treo made amps. No thanks, I like the DLS amp more as far as a trade. I would trade for a nice and powerful 3/5 channel but dont need speakers.
I do need a zapco dc ref 200.2
General info :
Size: 21"W x 3-5/16"H x 12"D
Single-ended push/pull design for stability at 1 and 0.5 ohm
Discrete differential inputs for reduced noise
Dual power supplies
The C and D channels can be set for Hi-Current or Hi-Voltage operation; the A and B channels are permanently set to Hi-Voltage operation (the A and B channels cannot be switched to Hi-Current operation).
The Hi-Current and Hi-Voltage modes differ as follows:
Hi-Current Mode allows you to connect a speaker or combination of speakers with an impedance as low as 0.5 ohm for a stereo load, or 1 ohm for a bridged load, to the C and D channels.
Hi-Voltage Mode allows you to connect a speaker or combination of speakers with an impedance of 2 to 8 ohms (4 ohms bridged) and provides better sound quality; the Hi-Voltage mode can be used for all four channels.
Pulse power supply regulates fluctuating voltage from a vehicle's battery while being light weight and highly efficient
Direct switch allows for best possible sound
Negative Feed Back circuit can be turned off for clearer sound
Independent voltage amplifier power supply
MOSFET Power Supply
Speaker terminal short circuit
Indicators on top of unit:
Mode indicator: One of two LEDs illuminate to show if the amp is in High-Current or Hi-Voltage mode
Over Current LED illuminates in green during normal operation, switches to amber during an over-current situation
Offset LED illuminates in green during normal operation, switches to amber when voltage going out is too high
Thermal LED illuminates in green during normal operation, switches to amber when the temperature rises to an unsafe level
Best frequency response: 5Hz - 100 kHz (+0/-3dB)
Inputs, Outputs, & Controls
Inputs, Outputs and Controls (all located on front of unit under removal terminal cover):
Gold plated stereo RCA inputs for front and rear channels.
Ground and +12v inputs: Gold plated terminal strip, note that there are two of each of these.
Remote input: Spring clip, accepts wire with AWG 22-16.
Hi-Current/Hi-Voltage switch: Allows you to select operating mode for the C and D channels.
Test Tone recessed button: When pressed puts out a test tone that indicates that the unit is operating properly.
Speaker outputs: For A, B, C and D speakers, two gold plated terminal strips. Bridged mode uses the L+ and R- terminal outputs.
Low Boost level knobs: Two knobs, one for the A/B channels, the other for the C/D channels. Allows you to boost bass by 0 to +10dB (centered at 40Hz).
Level Controls: Two knobs, one for channels AB the other for channels CD. Used to set input level
Direct Switches: Two switches, one for channels AB the other for channels CD. Can turn on or off. In the ON position the input signal does not go through the crossover or bass boost circuitry, which results in a cleaner signal for better sound quality.
Frequency Adjustment controls: Two controls, one for channels AB the other for channels CD, can be varied from 50Hz to 400Hz.
X10 Switches: Two switches, one for channels AB the other for channels CD, used to change crossover frequencies from 50-400Hz to 500Hz to 4kHz
Filter switches: Two crossover switches. Allows you to select low pass, high pass or off for the front and rear channels.
NFB switch: Negative Feed Back switch. Can select on and off, when on negative feed back is applied which reduces certain types of amplifier distortion but which some people claim muddies the sound. Note that usually all amplifiers except high end amplifiers use negative feed back. This switch effects A,B, C and D channels.
99 Honda CRV: (Always Changing) ___________ 79 F-150: Show Truck ________________
-Head Unit: Eclipse CD7100________________ -Head Unit: Eclipse CD7100
-Sub Stage: Sundown SD-2 8's sealed________ -Sub Stage: Looking
-Mids/Highs: Deciding_____________________ -Mids/Highs: Scan Speak & Blaupunkt
-Sub Amp: MMATS Hifi 6 channel____________ -Sub Amp: American Warrior Set (Zed Built)
-Mid Amp: ^^^ 5/6 bridged at 1 ohm_________ -Mid Amp: ^^^
Refs: mrmakinmoves[SCAMMER] AKA ICHASEPAPER2010, skydeaner, fukinmovin, mossberg385t, grimreper912003, LBC99, Dbeez, Michaellane, thegreatestpenn, truckstoy, ge_off_me, btr, cupid6969, johnprdeye, jh8909, tylerj, UMWDawg92, nu2spl, zerosktr111, SPLAUDIO, $LICK CALIFA$, jfroghobo