Closed Thread
Results 1 to 4 of 4

Reload Thread: Having an issue with my system. Somone help me figure it out. Alpine & Zapco gurus

  1. #1
    SPLAudioHz's Avatar
    SPLAudioHz is offline Senior VIP Member



    Join Date
    Sep 2010
    Location
    Indiana
    Posts
    371
    Post Thanks / Like
    Mentioned
    1 Post(s)

    Having an issue with my system. Somone help me figure it out. Alpine & Zapco gurus

    Hey guys, I got my system hooked up tonight.
    95 Mustang 5.0 Build Log

    So for now I am NOT running a sub, or center channel, or rear fill. I just want to get the front stage set before I add too much. So on my Zapco DC Ref 650.6 I have the symbilink for channels 5/6 plugged in.
    To fill you in on my HU, it is a CDA117. After a long chat with Alpine I was informed to switch the switches on the underside of the HU to the side opposite or "Normal" since the Imprint module is where the the amp is getting its info.
    I took the left channel RCA for the front and plugged it in. No sound but I figure it is because I need to plug the amp in to my laptop and set gains as the Prev owner did not use those channels.
    I plug in the red RCA and I get a rapid popping from my front speaker and the protect light on my symbilink is flashing to the popping. I was like SH|T! Well I figured I may have wired that side wrong (this is a huuuuge maybe because I labeled and rechecked wires more than a dozen times as well as photographed every step), so I swapped the rcas around. The other speakers also did the same thing!!! Well SH|T again.

    Anyone have any insight on this? Thoughts, suggestions?

    Thanks a ton,

    Jesse







  2. #2
    sacsking916's Avatar
    sacsking916 is offline stayin high an loud



    Join Date
    Apr 2009
    Location
    emerald triangle..home of da trees
    Posts
    6,428
    Post Thanks / Like
    Mentioned
    6 Post(s)

    Re: Having an issue with my system. Somone help me figure it out. Alpine & Zapco guru

    Bad rcas? Or possible bad RCA on the hu. Happened to me on my old Kenwood but no popping




    TEAM AUDIO TECHNIX
    TEAM SSC
    TEAM CADENCE
    Sold to: imtjnotu; ace_800; omegabunny crazykenkid Bought from: El_weenie; fasfocus00; retroaudioinc; f1mclarenagr; jason19; tone415; twizted859; noph33rracing; tony30cl; carlosg_313 Traded with: Micah_Jones; MikeOfTulsa
    Quote Originally Posted by audioholic View Post
    Apparently I was called out, or called a goat fucker, or something. I really have no idea. Im just along for the ride at this point.
    Quote Originally Posted by CRXBMPN View Post
    King James has nothing on King Sac!

  3. #3
    SPLAudioHz's Avatar
    SPLAudioHz is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2010
    Location
    Indiana
    Posts
    371
    Post Thanks / Like
    Mentioned
    1 Post(s)

    Re: Having an issue with my system. Somone help me figure it out. Alpine & Zapco guru

    I thought the same thing, but I tried all 3 sets of RCAs. Ixos kind of narrows down the chance for errors. I will check that though, Might try a direct connect to the HU rather than through the Imprint.




  4. #4
    Xenophile's Avatar
    Xenophile is offline Junior Member



    Join Date
    Jun 2011
    Location
    Nashville TN.
    Posts
    13
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Having an issue with my system. Somone help me figure it out. Alpine & Zapco guru

    i would disconnect my speaker wires at the amp and check for a short to ground or bad voicecoil you should get a known good speaker to use as a test speaker hook it to your amp and see if the problem is still present then with the amp on if the noise is still there disconnect the input to the amp and see if it goes away that will narrow it down to 3 things either a bad speaker or wire run,a bad amp,or a bad feed to the amp the fastest test is to disconnect the input from the amp so do that first




Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum