**poundindak69 shady seller/beware**

[poundindak69]

thats not what i asked.. i was asking how long from when u shipped it did u take it out..EX:::::A WEEK? 5 DAYS? WHAT

it was out the 1st of november and it shipped on the 13 so almost 2 weeks

[silvercookie]

then who bent it?
the ****ing boogey man?

[poundindak69]

as far as i know from now u are and always will be a shady seller and never bought from again.. the fact that it took you until i made a thread to start talking to me.. is complete bs

yeah i know but im not always on the computer when im sitting around....i would of prolly kept better contact with you through pms and im trying to get this straightened out...i just dont understand how im shaddy im more like poor customer service...

[brtnboarder3241]

it was out the 1st of november and it shipped on the 13 so almost 2 weeks

u can remember that but not to inform me even 1 word to say that my amp broke when we talked... or to even try to contact me... or even remember the day the amp broke..

[poundindak69]

then who bent it?
the ****ing boogey man?

well i know that i didnt not....

[silvercookie]

well i know that i didnt not....

then how did it get bent

do you know how much force it takes to bend a solid steel plate like that?

a good 300 or so pounds of pressure.

or a drop off something about 3-4 feet in the air.

[poundindak69]

u can remember that but not to inform me even 1 word to say that my amp broke when we talked... or to even try to contact me... or even remember the day the amp broke..

no i had to go look back at my thread to remember when i took it out.....and i figured the amp blowing was my problem

[poundindak69]

then how did it get bent

do you know how much force it takes to bend a solid steel plate like that?

a good 300 or so pounds of pressure.

or a drop off something about 3-4 feet in the air.

yes i do know that.... and it did not fall or have that kind of pressure on it while it was in my possesion(sp?)

[brtnboarder3241]

no i had to go look back at my thread to remember when i took it out.....and i figured the amp blowing was my problem

apparently not when u talked to me... you stated "yes" after me asking if you thought that we were even cause the orion broke... sounds like to me you didnt think it was your problem

[brtnboarder3241]

^^^^^^referring to post above..

17:48] brtnboarder3241: dont take this personall bad
[17:48] brtnboarder3241: but then how is it even(or considered my fault)
[17:48] brtnboarder3241: ?
[17:48] xxxxxx: im not sayin was your fault
[17:48] brtnboarder3241: but from what you were saying we were "even"
[17:49] brtnboarder3241: or at least portraying man
[17:49] xxxxxxx: yeah
[17:49] brtnboarder3241: why are we even
[17:49] brtnboarder3241: i got a less described amp
[17:49] brtnboarder3241: u got a better descrbed amp
[17:49] brtnboarder3241: ?
[17:49] xxxxxxx: did i gaurente that is was goin to be delivered in perfect condition execpt for it bein blown

[silvercookie]

yes i do know that.... and it did not fall or have that kind of pressure on it while it was in my possesion(sp?)

well it couldnt have happened during shipping
unless the monkeys at ups took it out.
smashed it with a rubber mallet and put it back in

just stop lying it goes no one anywhere.

if you would have been honest brtn would have probably just said w/e
and just asked the money it would cost to get it bent back or fixed.

[poundindak69]

apparently not when u talked to me... you stated "yes" after me asking if you thought that we were even cause the orion broke... sounds like to me you didnt think it was your problem

well i was in a bad mood and i was being a *******....

[TurdFergueson2]

then how did it get bent

do you know how much force it takes to bend a solid steel plate like that?

a good 300 or so pounds of pressure.

or a drop off something about 3-4 feet in the air.

Like off a dresser in your room? I see what you're getting at........

[poundindak69]

well it couldnt have happened during shipping
unless the monkeys at ups took it out.
smashed it with a rubber mallet and put it back in

just stop lying it goes no one anywhere.

if you would have been honest brtn would have probably just said w/e
and just asked the money it would cost to get it bent back or fixed.

but im not lying im telling the truth......and so i was being honest with him

[poundindak69]

Like off a dresser in your room? I see what you're getting at........

uh no im the only person that goes in there so i know that it did not fall off the desser