LinkBack URL
About LinkBacksgood info in this thread thanks db-r
What it is hoe
good info in this thread thanks db-r
Tits.
Junior Member
Your not kidding......I have learned a lot from db-r in this thread, but my mind is still doing this.....Originally Posted by TreyE
2002 Tahoe
6K RMS watts using 2 AudioPipe AP3001d's / 4 18" AQ HDC3's / DC Power Dual alt setup / 3 Deka 9A31H's AGM / MLA 15.4v dual alt module / etc........
CarAudio.com Elite
that is the new 09 board you have a pix of dbr. they changed the power terminals on the 09 15001 and they are @ a downward angle. dont like!
9mm xmax = 25mm xmech
Interesting info about surface-mounting... I didn't realize that they have significantly lower power rating.
For all the surface-mount parts I've done, it's been a thin soldering iron tip, and a steady hand with the tweezers. Quite a pain, but it gets the job done. I've heard about the irons that "blow heat" but never used one. Sounds alot easier to use.
I'm guessing this is one of the reasons you always advise people not to mount amps to sub boxes?Vibration failure is alot more likely.
@ SPL, the terminals are angled down... for no good reason... It's not the worst thing ever, but alot of manufacturers are choosing this "upgrade". Is it for clean wiring?
1996 Toyota RAV4 - USACi Street Beat 1 Noob
Subs: Pioneer Premier TS-W2501D4 x 2
Amp: Audiopipe AP15001D
Box: 2 cf sealed (daily) and ?? Hz for comps
DC 200 amp alt + YellowTop + Big 3 + 1/0 welding wire + gobs of Peel N Seal
CarAudio.com Elite
It's because too I think that if you mount the board in a case that has those SNAZZY end caps like Memphis uses (yuck) made of plastic instead of METAL because the plastic shiz is cheaper it makes for cleaner wiring yes...
CarAudio.com Veteran
nope not at allCool story brah, u mad
I will say that after seeing the pics posted of the new line, that I am impressed with the differences, 105 celcius caps, thats always a good thing. the 15001 i saw ( several of them ) were all 85 celcius IIRC. so at least that and the new thicker wire is a good thing. hell at 150$ i may try 1 as a test amp on the bench lolz.
sold to: Pumkinman, j1b1e1, DexterMoped, miyagi gboo559,CSU87,nate2587, MichaelLane, SmLLySack. MR_Imperial, Herrrerra, ltr450racer690
bought from: TripleB45, bigwheel15
if you don't like it too fucking bad, suck my dick
wow makes them feel special to change my sig
really mature
feedback thread :http://www.caraudio.com/forum/showth...audio+feedback
so tell the rest of the people the same thing
Senior VIP Member
^Well get on it.
Junior Member
my 2 come tomorrow, cant wait to take there covers off, and peak inside! Anyone of you want to see the gut shots of the 08/09 model?
2002 Tahoe
6K RMS watts using 2 AudioPipe AP3001d's / 4 18" AQ HDC3's / DC Power Dual alt setup / 3 Deka 9A31H's AGM / MLA 15.4v dual alt module / etc........
9mm xmax = 25mm xmech
should be pretty similar, but I'd enjoy the peep show.
need to get some thermal grease, so I can check the FET model number. may be a couple days.
1996 Toyota RAV4 - USACi Street Beat 1 Noob
Subs: Pioneer Premier TS-W2501D4 x 2
Amp: Audiopipe AP15001D
Box: 2 cf sealed (daily) and ?? Hz for comps
DC 200 amp alt + YellowTop + Big 3 + 1/0 welding wire + gobs of Peel N Seal
CarAudio.com Veteran
are these strappable?
GMC Jimmy 1999
HU: Jensen Indash touchscreen dvd
FrontStage: 4 Soundstream 6.5 components
FS Amp: Cadence TXA3004
SUBS: Bravox EDX 18s I built walled behind the back seats
SUB AMP: clif designs 4800.1lx
Feedback: MakeshiftAudio, woofercooker, vitveet, jonesy, 2000gator, KickerRex, mathewo, Matt2105, sicaudio, kshutte, coma-toast, RAB, matt2105, jusbloud and more that i cant remember.
CarAudio.com Elite
Already posted
Sold to: caco- whitetb,get_low,zlibby76,nuboot
caraudio.com- lowrnu,gbody805,rdwilson77,Kodak314,Mr.tigger
Junior Member
alright i know im new here and i know this is an old topic but has anyone had the
AP30001D at one ohm bridged?
Rourke's my homie!!
I have mine at 1.4 daily
Snappin' necks and cashin' checks
Feedback thread:http://www.caraudio.com/forum/buyer-seller-feedback/406357-annarbor84-feedback-thread.html
Sold to: sixfootman2005, MTX520, JHardee, smd4life, KyleBechtold, IA2, DaBeholder
Traded with: BushJ311
Bought from: Blinkdogo2, audioarsonal, 528hz, kasimo420, wasted ink, Tehgregzor, Spy, Rio
cj407 <------Slowing tracks, here's the man
CarAudio.com Veteran
I just bought a black ap30001d. Plan on running it at 2ohm hopefully imp rise wont hurt me too bad. Has anyone tried 1 ohm on it?
Alpine 9884
Alpine 609 6x9s
SA Nightshade 18''
AQ2200
C&D 134AH rate battery
'04 Dodge Ram 1500 Single Cab
Refs: midwestcustoms3 ; dadon ; DBBOOM ; stevexyz ; Twisted_0912 ; on1wheel01 ; vitveet ; basscort2009 ; TeamPSI ; hotboxn ; xbearxlawls (SCAMMER) ; annarbor84 ; trailz516 ; Pioneer~Saturn ; dub22 ; Kern417 ; jbizzle ; wgsj_fortvalley
Rourke's my homie!!
Mine is black, look above
Snappin' necks and cashin' checks
Feedback thread:http://www.caraudio.com/forum/showthread.php?t=406357
Sold to: sixfootman2005, MTX520, JHardee, smd4life, KyleBechtold, IA2, DaBeholder
Traded with: BushJ311
Bought from: Blinkdogo2, audioarsonal, 528hz, kasimo420, wasted ink, Tehgregzor, Spy, Rio
cj407 <------Slowing tracks, here's the man
| ||||||||||||||||||||||
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions 
Reply With Quote
