Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Speakers
Wiring my speakers to my amp properly.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Siikdude" data-source="post: 8864539" data-attributes="member: 690407"><p>Hi there. So I have 4 of these Orion 6.5" Midrange Loudspeaker 1400 Watts Max 4 Ohm Hcca64n and anp orion The CBT4500.4. I have no idea if I have everything connected the best way to get the most out of the speakers. This is some specs of the amp (</p><p>4500W 4 Channel Class AB Amplifier</p><p>Peak Power at 2 Ohm: 4500 Watts | RMS Power at: 1300 Watts.</p><p>Stable at 2 Ohm, Frequency Response: 10Hz to 30kHz (-3dB)</p><p>Signal to Noise Ratio: 90dB)</p><p> And for the speaker this is the info I found (</p><p>Two 6.5" High-Efficiency Midrange Speakers</p><p>• 6.5" Black Paper Cone</p><p> • 1.5" High-Temperature CCAW Voice Coil</p><p>• Neodymium Magnet</p><p>• 350W RMS Each Speaker</p><p>• 700W Nominal Each Speaker</p><p> • 1400W Max Music Power Each Speaker</p><p>• 4 Ohm Impedance</p><p> • Sensitivity: 99 db/W/M</p><p> • Frequency Response: 130Hz-12KHz). I dont even know the correct wire gauge I need for them to be honest.</p></blockquote><p></p>
[QUOTE="Siikdude, post: 8864539, member: 690407"] Hi there. So I have 4 of these Orion 6.5" Midrange Loudspeaker 1400 Watts Max 4 Ohm Hcca64n and anp orion The CBT4500.4. I have no idea if I have everything connected the best way to get the most out of the speakers. This is some specs of the amp ( 4500W 4 Channel Class AB Amplifier Peak Power at 2 Ohm: 4500 Watts | RMS Power at: 1300 Watts. Stable at 2 Ohm, Frequency Response: 10Hz to 30kHz (-3dB) Signal to Noise Ratio: 90dB) And for the speaker this is the info I found ( Two 6.5" High-Efficiency Midrange Speakers • 6.5" Black Paper Cone • 1.5" High-Temperature CCAW Voice Coil • Neodymium Magnet • 350W RMS Each Speaker • 700W Nominal Each Speaker • 1400W Max Music Power Each Speaker • 4 Ohm Impedance • Sensitivity: 99 db/W/M • Frequency Response: 130Hz-12KHz). I dont even know the correct wire gauge I need for them to be honest. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Speakers
Wiring my speakers to my amp properly.
Top
Menu
Home
Refresh